Home » HP Manuals » Desktops » HP Pro 6305 » Manual Viewer

HP Pro 6305 Maintenance and Service Guide HP Compaq Pro 6305 Microtower Busine - Page 30

Computer Setup-Advanced for advanced users continued, Table 3-6

Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Table 3-6 Computer Setup-Advanced (for advanced users) (continued) Bus Options On some models, allows you to enable or disable: ● PCI SERR# Generation. Default is enabled. ● PCI VGA Palette Snooping, which sets the VGA palette snooping bit in PCI configuration space; only needed when more than one graphics controller is installed. Default is disabled. Device Options Allows you to set: ● Monitor Tracking (enable/disable). Allows ROM to save monitor asset information. Default is disabled. ● Printer mode (Bi-Directional, EPP + ECP, Output Only). Default is EPP+ECP. ● Num Lock State at Power-On (off/on). Default is off. ● Integrated Video (enable/disable). Use this option to disable the integrated video controller when another video controller is present in the system. Default is enabled. ● Integrated Video (Automatic UMA/Selectable UMA Size). Allows you to automatically or manually set UMA video size. Default is automatic. NOTE: If you choose Selectable UMA Size, a new menu item displays to allow you to select the UMA Frame Buffer Size. Default value is 256 MB. ● Internal Speaker (some models) (does not affect external speakers). Default is enabled. ● NIC PXE Option ROM Download (PXE, iSCSI, disabled). The BIOS contains an embedded NIC option ROM to allow the unit to boot through the network to a PXE server. This is typically used to download a corporate image to a hard drive. The NIC option ROM takes up memory space below 1MB commonly referred to as DOS Compatibility Hole (DCH) space. This space is limited. This F10 option will allow users to disable the downloading of this embedded NIC option ROM thus giving more DCH space for additional PCI cards which may need option ROM space. Default is enabled. ● NetClone Option ROM Download (enable/disable) (some models). This BIOS contains an embedded NetClone option. Use this option to enable or disable the NetClone BIOS. Default is disabled. ● SATA RAID Option ROM Download (enable/disable). The BIOS contains an embedded SATA RAID option ROM for RAID support. This can be temporarily disabled to save DCH space. Note that with the option ROM disabled, users will be unable to boot to hard drives in the system while running in RAID mode. Default is disabled. ● Multi-Processor (enable/disable). Use this option to disable multi-processor support under the OS. Default is enabled. 20 Chapter 3 Computer Setup (F10) Utility

Section	Page
Product Features	11
Standard Configuration Features	11
Microtower (MT) Front Panel Components	12
Small Form Factor (SFF) Front Panel Components	13
Microtower (MT) Rear Panel Components	14
Small Form Factor (SFF) Rear Panel Components	15
Serial Number Location	16
Installing and Customizing the Software	17
Installing the Windows operating system	17
Downloading Windows 7 updates	18
Installing or upgrading device drivers	18
Customizing the monitor display	18
Computer Setup (F10) Utility	19
Computer Setup (F10) Utilities	19
Using Computer Setup (F10) Utilities	20
Computer Setup—File	21
Computer Setup—Storage	22
Computer Setup—Security	25
Computer Setup—Power	28
Computer Setup—Advanced	29
Recovering the Configuration Settings	31
Illustrated parts catalog	32
Microtower (MT) chassis spare parts	32
Computer major components	32
Cables	34
Misc parts	35
Drives	37
Misc boards	37
Sequential part number listing	38
Small Form Factor (SFF) chassis spare parts	41
Computer major components	41
Cables	43
Misc parts	44
Drives	46
Misc boards	46
Sequential part number listing	47
Routine Care, SATA Drive Guidelines, and Disassembly Preparation	50
Electrostatic Discharge Information	50
Generating Static	50
Preventing Electrostatic Damage to Equipment	51
Personal Grounding Methods and Equipment	51
Grounding the Work Area	52
Recommended Materials and Equipment	52
Operating Guidelines	53
Routine Care	53
General Cleaning Safety Precautions	53
Cleaning the Computer Case	53
Cleaning the Keyboard	54
Cleaning the Monitor	54
Cleaning the Mouse	55
Service Considerations	55
Power Supply Fan	55
Tools and Software Requirements	55
Screws	55
Cables and Connectors	56
Hard Drives	56
Lithium Coin Cell Battery	56
SATA Hard Drives	57
SATA Hard Drive Cables	57
SATA Data Cable	57
SMART ATA Drives	57
Cable Management	57
Hard Drive Capacities	58
Removal and Replacement Procedures Microtower (MT) Chassis	59
Preparation for Disassembly	59
Computer Access Panel	60
Front Bezel	61
Front Bezel Security	62
Bezel Blanks	64
Memory	65
DIMMs	65
DDR3-SDRAM DIMMs	65
Populating DIMM Sockets	66
Installing DIMMs	66
Expansion Cards	68
System Board Connections	72
Drives	73
Drive Positions	75
Removing a 5.25-inch or 3.5-inch Drive from a Drive Bay	76
Installing a 5.25-inch or 3.5-inch Drive into a Drive Bay	77
Removing a Hard Drive from a Drive Bay	80
Installing a Hard Drive into an Internal Drive Bay	81
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	83
Front Fan Assembly	88
Front I/O Assembly	90
Power Switch/LED Assembly	91
Heat sink	92
Processor	94
Speaker	95
Rear Chassis Fan	96
Power Supply	98
System Board	100
Removal and Replacement Procedures Small Form Factor (SFF) Chassis	102
Preparation for Disassembly	102
Access Panel	103
Front Bezel	104
Front Bezel Security	105
Bezel Blanks	107
Memory	108
DIMMs	108
DDR3-SDRAM DIMMs	108
Populating DIMM Sockets	108
Installing DIMMs	109
Expansion Card	111
System Board Connections	115
Drives	116
Drive Positions	117
Installing and Removing Drives	117
Removing a 5.25-inch Drive from a Drive Bay	118
Installing a 5.25-inch Drive into a Drive Bay	119
Removing a 3.5-inch Drive from a Drive Bay	121
Installing a 3.5-inch Drive into a Drive Bay	123
Removing and Replacing the Primary 3.5-inch Internal Hard Drive	125
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	127
Fan duct	132
Front Fan Assembly	133
Hood Sensor	135
Front I/O, Power Switch Assembly	136
Speaker	138
Heat sink	139
Processor	141
Power Supply	142
System Board	144
Using the Small Form Factor Computer in a Tower Orientation	146
Troubleshooting Without Diagnostics	147
Safety and Comfort	147
Before You Call for Technical Support	147
Helpful Hints	148
Solving General Problems	150
Solving Power Problems	154
Solving Hard Drive Problems	155
Solving Media Card Reader Problems	158
Solving Display Problems	160
Solving Audio Problems	164
Solving Printer Problems	166
Solving Keyboard and Mouse Problems	167
Solving Hardware Installation Problems	169
Solving Network Problems	171
Solving Memory Problems	173
Solving Processor Problems	175
Solving CD-ROM and DVD Problems	175
Solving USB Flash Drive Problems	178
Solving Front Panel Component Problems	179
Solving Internet Access Problems	179
Solving Software Problems	181
Contacting Customer Support	182
POST Error Messages	183
POST Numeric Codes and Text Messages	184
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes	192
Password Security and Resetting CMOS	196
Resetting the Password Jumper	197
Clearing and Resetting the CMOS	198
Restoring and recovering in Windows 7	200
System Restore	200
System Recovery	201
System Recovery when Windows is responding	201
System Recovery when Windows is not responding	202
System recovery using recovery media	202
Creating recovery media	203
Using recovery media	203
Battery Replacement	205
Power Cord Set Requirements	208
General Requirements	208
Japanese Power Cord Requirements	208
Country-Specific Requirements	209
Specifications	210
MT Specifications	210
SFF Specifications	212

Match case Limit results 1 per page

Table 3-6

Computer Setup—Advanced (for advanced users) (continued)

Bus Options

On some models, allows you to enable or disable:

●

PCI SERR# Generation. Default is enabled.

●

PCI VGA Palette Snooping, which sets the VGA palette snooping bit in PCI configuration

space; only needed when more than one graphics controller is installed. Default is disabled.

Device Options

Allows you to set:

●

Monitor Tracking (enable/disable). Allows ROM to save monitor asset information. Default is

disabled.

●

Printer mode (Bi-Directional, EPP + ECP, Output Only). Default is EPP+ECP.

●

Num Lock State at Power-On (off/on). Default is off.

●

Integrated Video (enable/disable). Use this option to disable the integrated video controller

when another video controller is present in the system. Default is enabled.

●

Integrated Video (Automatic UMA/Selectable UMA Size). Allows you to automatically or

manually set UMA video size. Default is automatic.

NOTE:

If you choose Selectable UMA Size, a new menu item displays to allow you to

select the UMA Frame Buffer Size. Default value is 256 MB.

●

Internal Speaker (some models) (does not affect external speakers). Default is enabled.

●

NIC PXE Option ROM Download (PXE, iSCSI, disabled). The BIOS contains an embedded

NIC option ROM to allow the unit to boot through the network to a PXE server. This is

typically used to download a corporate image to a hard drive. The NIC option ROM takes up

memory space below 1MB commonly referred to as DOS Compatibility Hole (DCH) space.

This space is limited. This F10 option will allow users to disable the downloading of this

embedded NIC option ROM thus giving more DCH space for additional PCI cards which may

need option ROM space. Default is enabled.

●

NetClone Option ROM Download (enable/disable) (some models). This BIOS contains an

embedded NetClone option. Use this option to enable or disable the NetClone BIOS. Default

is disabled.

●

SATA RAID Option ROM Download (enable/disable). The BIOS contains an embedded

SATA RAID option ROM for RAID support. This can be temporarily disabled to save DCH

space. Note that with the option ROM disabled, users will be unable to boot to hard drives in

the system while running in RAID mode. Default is disabled.

●

Multi-Processor (enable/disable). Use this option to disable multi-processor support under

the OS. Default is enabled.

Chapter 3

Computer Setup (F10) Utility