Home » HP Manuals » Desktops » HP Pro 6305 » Manual Viewer

HP Pro 6305 Maintenance and Service Guide HP Compaq Pro 6305 Microtower Busine - Page 57

SATA Hard Drives, SATA Data Cable, SMART ATA Drives, Cable Management

Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

SATA Hard Drives Serial ATA Hard Drive Characteristics Number of pins/conductors in data cable Number of pins in power cable Maximum data cable length Data interface voltage differential Drive voltages Jumpers for configuring drive Data transfer rate 7/7 15 39.37 in (100 cm) 400-700 mV 3.3 V, 5 V, 12 V N/A 3.0 Gb/s SATA Hard Drive Cables SATA Data Cable Always use an HP approved SATA 3.0 Gb/s cable as it is fully backwards compatible with the SATA 1.5 Gb/s drives. Current HP desktop products ship with SATA 3.0 Gb/s hard drives. SATA data cables are susceptible to damage if overflexed. Never crease a SATA data cable and never bend it tighter than a 30 mm (1.18 in) radius. The SATA data cable is a thin, 7-pin cable designed to transmit data for only a single drive. SMART ATA Drives The Self Monitoring Analysis and Recording Technology (SMART) ATA drives for the HP Personal Computers have built-in drive failure prediction that warns the user or network administrator of an impending failure or crash of the hard drive. The SMART drive tracks fault prediction and failure indication parameters such as reallocated sector count, spin retry count, and calibration retry count. If the drive determines that a failure is imminent, it generates a fault alert. Cable Management Always follow good cable management practices when working inside the computer. ● Keep cables away from major heat sources like the heat sink. ● Do not jam cables on top of expansion cards or memory modules. Printed circuit cards like these are not designed to take excessive pressure on them. ● Keep cables clear of sliding or moveable parts to prevent them from being cut or crimped when the parts are moved. ● When folding a flat ribbon cable, never fold to a sharp crease. Sharp creases may damage the wires. SATA Hard Drives 47

Section	Page
Product Features	11
Standard Configuration Features	11
Microtower (MT) Front Panel Components	12
Small Form Factor (SFF) Front Panel Components	13
Microtower (MT) Rear Panel Components	14
Small Form Factor (SFF) Rear Panel Components	15
Serial Number Location	16
Installing and Customizing the Software	17
Installing the Windows operating system	17
Downloading Windows 7 updates	18
Installing or upgrading device drivers	18
Customizing the monitor display	18
Computer Setup (F10) Utility	19
Computer Setup (F10) Utilities	19
Using Computer Setup (F10) Utilities	20
Computer Setup—File	21
Computer Setup—Storage	22
Computer Setup—Security	25
Computer Setup—Power	28
Computer Setup—Advanced	29
Recovering the Configuration Settings	31
Illustrated parts catalog	32
Microtower (MT) chassis spare parts	32
Computer major components	32
Cables	34
Misc parts	35
Drives	37
Misc boards	37
Sequential part number listing	38
Small Form Factor (SFF) chassis spare parts	41
Computer major components	41
Cables	43
Misc parts	44
Drives	46
Misc boards	46
Sequential part number listing	47
Routine Care, SATA Drive Guidelines, and Disassembly Preparation	50
Electrostatic Discharge Information	50
Generating Static	50
Preventing Electrostatic Damage to Equipment	51
Personal Grounding Methods and Equipment	51
Grounding the Work Area	52
Recommended Materials and Equipment	52
Operating Guidelines	53
Routine Care	53
General Cleaning Safety Precautions	53
Cleaning the Computer Case	53
Cleaning the Keyboard	54
Cleaning the Monitor	54
Cleaning the Mouse	55
Service Considerations	55
Power Supply Fan	55
Tools and Software Requirements	55
Screws	55
Cables and Connectors	56
Hard Drives	56
Lithium Coin Cell Battery	56
SATA Hard Drives	57
SATA Hard Drive Cables	57
SATA Data Cable	57
SMART ATA Drives	57
Cable Management	57
Hard Drive Capacities	58
Removal and Replacement Procedures Microtower (MT) Chassis	59
Preparation for Disassembly	59
Computer Access Panel	60
Front Bezel	61
Front Bezel Security	62
Bezel Blanks	64
Memory	65
DIMMs	65
DDR3-SDRAM DIMMs	65
Populating DIMM Sockets	66
Installing DIMMs	66
Expansion Cards	68
System Board Connections	72
Drives	73
Drive Positions	75
Removing a 5.25-inch or 3.5-inch Drive from a Drive Bay	76
Installing a 5.25-inch or 3.5-inch Drive into a Drive Bay	77
Removing a Hard Drive from a Drive Bay	80
Installing a Hard Drive into an Internal Drive Bay	81
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	83
Front Fan Assembly	88
Front I/O Assembly	90
Power Switch/LED Assembly	91
Heat sink	92
Processor	94
Speaker	95
Rear Chassis Fan	96
Power Supply	98
System Board	100
Removal and Replacement Procedures Small Form Factor (SFF) Chassis	102
Preparation for Disassembly	102
Access Panel	103
Front Bezel	104
Front Bezel Security	105
Bezel Blanks	107
Memory	108
DIMMs	108
DDR3-SDRAM DIMMs	108
Populating DIMM Sockets	108
Installing DIMMs	109
Expansion Card	111
System Board Connections	115
Drives	116
Drive Positions	117
Installing and Removing Drives	117
Removing a 5.25-inch Drive from a Drive Bay	118
Installing a 5.25-inch Drive into a Drive Bay	119
Removing a 3.5-inch Drive from a Drive Bay	121
Installing a 3.5-inch Drive into a Drive Bay	123
Removing and Replacing the Primary 3.5-inch Internal Hard Drive	125
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	127
Fan duct	132
Front Fan Assembly	133
Hood Sensor	135
Front I/O, Power Switch Assembly	136
Speaker	138
Heat sink	139
Processor	141
Power Supply	142
System Board	144
Using the Small Form Factor Computer in a Tower Orientation	146
Troubleshooting Without Diagnostics	147
Safety and Comfort	147
Before You Call for Technical Support	147
Helpful Hints	148
Solving General Problems	150
Solving Power Problems	154
Solving Hard Drive Problems	155
Solving Media Card Reader Problems	158
Solving Display Problems	160
Solving Audio Problems	164
Solving Printer Problems	166
Solving Keyboard and Mouse Problems	167
Solving Hardware Installation Problems	169
Solving Network Problems	171
Solving Memory Problems	173
Solving Processor Problems	175
Solving CD-ROM and DVD Problems	175
Solving USB Flash Drive Problems	178
Solving Front Panel Component Problems	179
Solving Internet Access Problems	179
Solving Software Problems	181
Contacting Customer Support	182
POST Error Messages	183
POST Numeric Codes and Text Messages	184
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes	192
Password Security and Resetting CMOS	196
Resetting the Password Jumper	197
Clearing and Resetting the CMOS	198
Restoring and recovering in Windows 7	200
System Restore	200
System Recovery	201
System Recovery when Windows is responding	201
System Recovery when Windows is not responding	202
System recovery using recovery media	202
Creating recovery media	203
Using recovery media	203
Battery Replacement	205
Power Cord Set Requirements	208
General Requirements	208
Japanese Power Cord Requirements	208
Country-Specific Requirements	209
Specifications	210
MT Specifications	210
SFF Specifications	212

Match case Limit results 1 per page

SATA Hard Drives

Serial ATA Hard Drive Characteristics

Number of pins/conductors in data cable

7/7

Number of pins in power cable

Maximum data cable length

39.37 in (100 cm)

Data interface voltage differential

400-700 mV

Drive voltages

3.3 V, 5 V, 12 V

Jumpers for configuring drive

N/A

Data transfer rate

3.0 Gb/s

SATA Hard Drive Cables

SATA Data Cable

Always use an HP approved SATA 3.0 Gb/s cable as it is fully backwards compatible with the SATA

1.5 Gb/s drives.

Current HP desktop products ship with SATA 3.0 Gb/s hard drives.

SATA data cables are susceptible to damage if overflexed. Never crease a SATA data cable and

never bend it tighter than a 30 mm (1.18 in) radius.

The SATA data cable is a thin, 7-pin cable designed to transmit data for only a single drive.

SMART ATA Drives

The Self Monitoring Analysis and Recording Technology (SMART) ATA drives for the HP Personal

Computers have built-in drive failure prediction that warns the user or network administrator of an

impending failure or crash of the hard drive. The SMART drive tracks fault prediction and failure

indication parameters such as reallocated sector count, spin retry count, and calibration retry count. If

the drive determines that a failure is imminent, it generates a fault alert.

Cable Management

Always follow good cable management practices when working inside the computer.

●

Keep cables away from major heat sources like the heat sink.

●

Do not jam cables on top of expansion cards or memory modules. Printed circuit cards like these

are not designed to take excessive pressure on them.

●

Keep cables clear of sliding or moveable parts to prevent them from being cut or crimped when

the parts are moved.

●

When folding a flat ribbon cable, never fold to a sharp crease. Sharp creases may damage the

wires.

SATA Hard Drives