Home » HP Manuals » Desktops » HP Pro 6305 » Manual Viewer

HP Pro 6305 Maintenance and Service Guide HP Compaq Pro 6305 Microtower Busine - Page 83

Removing and Replacing a Removable 3.5-inch SATA Hard Drive, Sliding a Hard Drive into the Drive Bay

Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

4. Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until the drive snaps into place. The bottom bay is for the primary hard drive. The upper bay is for an optional secondary hard drive. Figure 6-27 Sliding a Hard Drive into the Drive Bay 5. Connect the power cable and data cable to the back of the hard drive. NOTE: The power cable for the hard drives is a two-headed cable that is routed from the system board to the rear of the hard drive bays. 6. If installing a new drive, connect the opposite end of the data cable to the appropriate system board connector. NOTE: If your system has only one SATA hard drive, you must connect the hard drive data cable to the dark blue connector labeled SATA0 to avoid any hard drive performance problems. If you are adding a second hard drive, connect the data cable to the light blue connector labeled SATA1. 7. Route the power and data cables in their cable retainers. 8. Replace the computer access panel. 9. Reconnect the power cord and any external devices, then turn on the computer. 10. Lock any security devices that were disengaged when the access panel was removed. Removing and Replacing a Removable 3.5-inch SATA Hard Drive Some models are equipped with a Removable SATA Hard Drive Enclosure in the 5.25-inch internal drive bay. The hard drive is housed in a carrier that can be quickly and easily removed from the drive bay. To remove and replace a drive in the carrier: NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. 1. Unlock the hard drive carrier with the key provided and slide the carrier out of the enclosure. Drives 73

Section	Page
Product Features	11
Standard Configuration Features	11
Microtower (MT) Front Panel Components	12
Small Form Factor (SFF) Front Panel Components	13
Microtower (MT) Rear Panel Components	14
Small Form Factor (SFF) Rear Panel Components	15
Serial Number Location	16
Installing and Customizing the Software	17
Installing the Windows operating system	17
Downloading Windows 7 updates	18
Installing or upgrading device drivers	18
Customizing the monitor display	18
Computer Setup (F10) Utility	19
Computer Setup (F10) Utilities	19
Using Computer Setup (F10) Utilities	20
Computer Setup—File	21
Computer Setup—Storage	22
Computer Setup—Security	25
Computer Setup—Power	28
Computer Setup—Advanced	29
Recovering the Configuration Settings	31
Illustrated parts catalog	32
Microtower (MT) chassis spare parts	32
Computer major components	32
Cables	34
Misc parts	35
Drives	37
Misc boards	37
Sequential part number listing	38
Small Form Factor (SFF) chassis spare parts	41
Computer major components	41
Cables	43
Misc parts	44
Drives	46
Misc boards	46
Sequential part number listing	47
Routine Care, SATA Drive Guidelines, and Disassembly Preparation	50
Electrostatic Discharge Information	50
Generating Static	50
Preventing Electrostatic Damage to Equipment	51
Personal Grounding Methods and Equipment	51
Grounding the Work Area	52
Recommended Materials and Equipment	52
Operating Guidelines	53
Routine Care	53
General Cleaning Safety Precautions	53
Cleaning the Computer Case	53
Cleaning the Keyboard	54
Cleaning the Monitor	54
Cleaning the Mouse	55
Service Considerations	55
Power Supply Fan	55
Tools and Software Requirements	55
Screws	55
Cables and Connectors	56
Hard Drives	56
Lithium Coin Cell Battery	56
SATA Hard Drives	57
SATA Hard Drive Cables	57
SATA Data Cable	57
SMART ATA Drives	57
Cable Management	57
Hard Drive Capacities	58
Removal and Replacement Procedures Microtower (MT) Chassis	59
Preparation for Disassembly	59
Computer Access Panel	60
Front Bezel	61
Front Bezel Security	62
Bezel Blanks	64
Memory	65
DIMMs	65
DDR3-SDRAM DIMMs	65
Populating DIMM Sockets	66
Installing DIMMs	66
Expansion Cards	68
System Board Connections	72
Drives	73
Drive Positions	75
Removing a 5.25-inch or 3.5-inch Drive from a Drive Bay	76
Installing a 5.25-inch or 3.5-inch Drive into a Drive Bay	77
Removing a Hard Drive from a Drive Bay	80
Installing a Hard Drive into an Internal Drive Bay	81
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	83
Front Fan Assembly	88
Front I/O Assembly	90
Power Switch/LED Assembly	91
Heat sink	92
Processor	94
Speaker	95
Rear Chassis Fan	96
Power Supply	98
System Board	100
Removal and Replacement Procedures Small Form Factor (SFF) Chassis	102
Preparation for Disassembly	102
Access Panel	103
Front Bezel	104
Front Bezel Security	105
Bezel Blanks	107
Memory	108
DIMMs	108
DDR3-SDRAM DIMMs	108
Populating DIMM Sockets	108
Installing DIMMs	109
Expansion Card	111
System Board Connections	115
Drives	116
Drive Positions	117
Installing and Removing Drives	117
Removing a 5.25-inch Drive from a Drive Bay	118
Installing a 5.25-inch Drive into a Drive Bay	119
Removing a 3.5-inch Drive from a Drive Bay	121
Installing a 3.5-inch Drive into a Drive Bay	123
Removing and Replacing the Primary 3.5-inch Internal Hard Drive	125
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	127
Fan duct	132
Front Fan Assembly	133
Hood Sensor	135
Front I/O, Power Switch Assembly	136
Speaker	138
Heat sink	139
Processor	141
Power Supply	142
System Board	144
Using the Small Form Factor Computer in a Tower Orientation	146
Troubleshooting Without Diagnostics	147
Safety and Comfort	147
Before You Call for Technical Support	147
Helpful Hints	148
Solving General Problems	150
Solving Power Problems	154
Solving Hard Drive Problems	155
Solving Media Card Reader Problems	158
Solving Display Problems	160
Solving Audio Problems	164
Solving Printer Problems	166
Solving Keyboard and Mouse Problems	167
Solving Hardware Installation Problems	169
Solving Network Problems	171
Solving Memory Problems	173
Solving Processor Problems	175
Solving CD-ROM and DVD Problems	175
Solving USB Flash Drive Problems	178
Solving Front Panel Component Problems	179
Solving Internet Access Problems	179
Solving Software Problems	181
Contacting Customer Support	182
POST Error Messages	183
POST Numeric Codes and Text Messages	184
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes	192
Password Security and Resetting CMOS	196
Resetting the Password Jumper	197
Clearing and Resetting the CMOS	198
Restoring and recovering in Windows 7	200
System Restore	200
System Recovery	201
System Recovery when Windows is responding	201
System Recovery when Windows is not responding	202
System recovery using recovery media	202
Creating recovery media	203
Using recovery media	203
Battery Replacement	205
Power Cord Set Requirements	208
General Requirements	208
Japanese Power Cord Requirements	208
Country-Specific Requirements	209
Specifications	210
MT Specifications	210
SFF Specifications	212

Match case Limit results 1 per page

Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until

the drive snaps into place. The bottom bay is for the primary hard drive. The upper bay is for an

optional secondary hard drive.

Figure 6-27

Sliding a Hard Drive into the Drive Bay

Connect the power cable and data cable to the back of the hard drive.

NOTE:

The power cable for the hard drives is a two-headed cable that is routed from the

system board to the rear of the hard drive bays.

If installing a new drive, connect the opposite end of the data cable to the appropriate system

board connector.

NOTE:

If your system has only one SATA hard drive, you must connect the hard drive data

cable to the dark blue connector labeled SATA0 to avoid any hard drive performance problems.

If you are adding a second hard drive, connect the data cable to the light blue connector labeled

SATA1.

Route the power and data cables in their cable retainers.

Replace the computer access panel.

Reconnect the power cord and any external devices, then turn on the computer.

10.

Lock any security devices that were disengaged when the access panel was removed.

Removing and Replacing a Removable 3.5-inch SATA Hard Drive

Some models are equipped with a Removable SATA Hard Drive Enclosure in the 5.25-inch internal

drive bay. The hard drive is housed in a carrier that can be quickly and easily removed from the drive

bay. To remove and replace a drive in the carrier:

NOTE:

Before you remove the old hard drive, be sure to back up the data from the old hard drive so

that you can transfer the data to the new hard drive.

Unlock the hard drive carrier with the key provided and slide the carrier out of the enclosure.

Drives