HP Z600 HP Z Workstation series User Guide - Page 49

Remove the memory and system fans as shown in the following illustrations, if applicable.

Get HP Z600 - Workstation - 6 GB RAM PDF manuals and user guides
UPC - 884962074053
View all HP Z600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Z400 Z600 Z800 Pull up on the handle (1), slide the cover 1/2-inch toward the rear of the system (2), then rotate the cover off the chassis (3). Lift the side access panel handle (1), and remove the side access panel (2). Lift the side access panel handle (1), and remove the side access panel (2). 4. Remove the expansion card clamp or support as shown in the following illustrations, as applicable. Z400 Some Z400s use a hold down clamp; grasp the top of the clamp (1), squeeze the release handles on the side of the clamp until the bottom of the clamp releases from the clamp rail (2), then swing the clamp out from the back panel (3). Some Z400s have a card support. Remove the card support screws (1), and then lift the expansion card support from the chassis (2). Z800 Lift the release tab (1), and then lift the expansion card support handle (2) to remove the expansion card support. 5. Remove the memory and system fans as shown in the following illustrations, if applicable. ENWW Preparing the workstation for component installation 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Z400
Z600
Z800
Pull up on the handle (1), slide the
cover 1/2-inch toward the rear of the
system (2), then rotate the cover off the
chassis (3).
Lift the side access panel handle (1),
and remove the side access panel (2).
Lift the side access panel handle (1),
and remove the side access panel (2).
4.
Remove the expansion card clamp or support as shown in the following illustrations, as applicable.
Z400
Some Z400s use a hold down clamp; grasp the top of the
clamp (1), squeeze the release handles on the side of the
clamp until the bottom of the clamp releases from the clamp
rail (2), then swing the clamp out from the back panel (3).
Some Z400s have a card support. Remove the card
support screws (1), and then lift the expansion card support
from the chassis (2).
Z800
Lift the release tab (1), and then lift the expansion card support handle (2) to remove the expansion card support.
5.
Remove the memory and system fans as shown in the following illustrations, if applicable.
ENWW
Preparing the workstation for component installation
41