HP Z600 HP Z Workstation series User Guide - Page 65

HP Z600 - Workstation - 6 GB RAM Manual

Get HP Z600 - Workstation - 6 GB RAM PDF manuals and user guides
UPC - 884962074053
View all HP Z600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

5. Rotate the hard disk drive handle down into its fully open position. Carefully push the drive into its slot until comes to a hard stop (1) as shown in the following illustration. (An HP Z600 Workstation is shown for example.) When the hard disk drive is installed, rotate the drive handle up until it snaps into place, fully securing the drive (2). NOTE: The hard disk drive carrier handle is used as a lever to properly seat the connectors and to securely retain the drive. If the handle is closed prematurely, the proper connection is not made and the drive is not retained properly. Figure 9-6 Installing the HDD in the chassis 6. When installing a SAS hard disk drive in a Z600 Workstation, a SAS Controller card must be installed. Move the drive data cable from the system board SATA connector to the SAS Controller card connector. When installing a SAS hard disk drive in the Z800, move the drive data cable from the system board SATA connector to a system board SAS connector. See the workstation Maintenance and Service Guide for connector locations and installation details. 7. Replace all components that were removed in preparation for component installation. ENWW Installing a hard disk drive 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
5.
Rotate the hard disk drive handle down into its fully open position. Carefully push the drive into its
slot until comes to a hard stop (1) as shown in the following illustration. (An HP Z600 Workstation
is shown for example.)
When the hard disk drive is installed, rotate the drive handle up until it snaps into place, fully
securing the drive (2).
NOTE:
The hard disk drive carrier handle is used as a lever to properly seat the connectors and
to securely retain the drive. If the handle is closed prematurely, the proper connection is not made
and the drive is not retained properly.
Figure 9-6
Installing the HDD in the chassis
6.
When installing a SAS hard disk drive in a Z600 Workstation, a SAS Controller card must be
installed. Move the drive data cable from the system board SATA connector to the SAS Controller
card connector.
When installing a SAS hard disk drive in the Z800, move the drive data cable from the system board
SATA connector to a system board SAS connector.
See the workstation
Maintenance and Service Guide
for connector locations and installation
details.
7.
Replace all components that were removed in preparation for component installation.
ENWW
Installing a hard disk drive
57