IBM 2498-B40 User Guide - Page 46

Installing 8 Gbps SFP+ transceivers with wire bails

Get IBM 2498-B40 PDF manuals and user guides View all IBM 2498-B40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

b48f012 b32e4008 ! Figure 8. Installing a 16 Gbps SFP+ with pull tab (shown without cable attached) Installing 8 Gbps SFP+ transceivers with wire bails 1. Making sure that the bail (wire handle) is in the unlocked position, place the 8 Gbps SFP+ in the correctly oriented position on the port, as shown in Figure 9. 2. Slide the SFP+ into the port until you feel it click into place; then close the bail. ! Figure 9. SFP+ with wire bail latch 3. Orient a cable connector so that the key (the ridge on one side of the connector) aligns with the slot in the transceiver (see Figure 10). Then, insert the cable into the transceiver until the latching mechanism clicks. ! Figure 10. Installing a cable 4. Connect the other end of the cable to the appropriate device. Refer to "Planning for cable management" on page 7 for suggestions on organizing cables. 20 SAN48B-5 Installation, Service, and User Guide b48f013

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Installing 8 Gbps SFP+ transceivers with wire bails
1.
Making sure that the bail (wire handle) is in the unlocked position, place the 8
Gbps SFP+ in the correctly oriented position on the port, as shown in Figure 9.
2.
Slide the SFP+ into the port until you feel it click into place; then close the bail.
3.
Orient a cable connector so that the key (the ridge on one side of the connector)
aligns with the slot in the transceiver (see Figure 10). Then, insert the cable into
the transceiver until the latching mechanism clicks.
4.
Connect the other end of the cable to the appropriate device.
Refer to “Planning for cable management” on page 7 for suggestions on organizing
cables.
!
b48f012
Figure 8. Installing a 16 Gbps SFP+ with pull tab (shown without cable attached)
!
b32e4008
Figure 9. SFP+ with wire bail latch
!
b48f013
Figure 10. Installing a cable
20
SAN48B-5 Installation, Service, and User Guide