IBM 3580-L23 Setup Guide - Page 86

the function. The 3580 Ultrium 2 Tape Drive automatically starts the test one

Get IBM 3580-L23 PDF manuals and user guides View all IBM 3580-L23 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Ultrium Tape Drive Drive Empty 3. Within two seconds, press the unload button 3 times. The status light becomes solid amber and the following message displays (indicating that the tape drive is in maintenance mode): Maint Mode: Select Exit Maint Mode Note: If a cartridge is in the tape drive, it will eject the first time that you press the unload button and the drive will not be placed in maintenance mode. To continue placing the drive in maintenance mode, perform the preceding step. 4. Press the unload button once per second until 6 appears in the single-character display and the following message displays. (If you cycle past the desired code, press the unload button once per second until the code redisplays.) Maint Mode: Select SCSI Wrap [Inst Plug] 5. Make sure that the SCSI wrap plug is connected to one of the SCSI connectors at the rear of the 3580 Ultrium 2 Tape Drive. 6. Make sure that the 3580 Ultrium 2 Tape Drive is terminated at one of its SCSI connectors or at the SCSI bus. 7. Press and hold the unload button for 3 or more seconds, then release it to select the function. The 3580 Ultrium 2 Tape Drive automatically starts the test (one loop of which lasts for less than one second) and displays the following message: SCSI Wrap [Inst Plug] Running! v If no error is detected, the test will loop and begin again. To stop the loop, press the unload button for one second and release. When the loop ends, 0 temporarily appears in the single-character display. The following message displays: SCSI Wrap [Inst Plug] Passed! The drive then exits maintenance mode and displays the following message: Ultrium Tape Drive Drive Empty Disconnect the SCSI wrap plug. v If an error is detected, the test stops, 8 appears in the single-character display, and the following message displays: ERROR! Drive/SCSI Bus Error 70 IBM 3580 Ultrium Tape Drive Setup and Operator Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
Ultrium Tape Drive
Drive Empty
3.
Within two seconds, press the unload button 3 times. The status light becomes
solid amber and the following message displays (indicating that the tape drive
is in maintenance mode):
Maint Mode: Select
Exit Maint Mode
Note:
If a cartridge is in the tape drive, it will eject the first time that you press
the unload button and the drive will not be placed in maintenance
mode. To continue placing the drive in maintenance mode, perform the
preceding step.
4.
Press the unload button once per second until
6
appears in the single-character
display and the following message displays. (If you cycle past the desired code,
press the unload button once per second until the code redisplays.)
Maint Mode: Select
SCSI Wrap [Inst Plug]
5.
Make sure that the SCSI wrap plug is connected to one of the SCSI connectors
at the rear of the 3580 Ultrium 2 Tape Drive.
6.
Make sure that the 3580 Ultrium 2 Tape Drive is terminated at one of its SCSI
connectors or at the SCSI bus.
7.
Press and hold the unload button for 3 or more seconds, then release it to select
the function. The 3580 Ultrium 2 Tape Drive automatically starts the test (one
loop of which lasts for less than one second) and displays the following
message:
SCSI Wrap [Inst Plug]
Running!
v
If no error is detected, the test will loop and begin again. To stop the loop,
press the unload button for one second and release. When the loop ends,
0
temporarily appears in the single-character display. The following message
displays:
SCSI Wrap [Inst Plug]
Passed!
The drive then exits maintenance mode and displays the following message:
Ultrium Tape Drive
Drive Empty
Disconnect the SCSI wrap plug.
v
If an error is detected, the test stops,
8
appears in the single-character
display, and the following message displays:
ERROR!
Drive/SCSI Bus Error
70
IBM 3580 Ultrium Tape Drive Setup and Operator Guide