IBM 3580-L23 Setup Guide - Page 96

If no error is detected, the test will loop and begin again. To stop the loop

Get IBM 3580-L23 PDF manuals and user guides View all IBM 3580-L23 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

4. Press the unload button once per second until H appears in the single-character display and the following message displays. (If you cycle past the desired code, press the unload button once per second until the code redisplays.) Maint Mode: Select Test Head 5. Press and hold the unload button for 3 or more seconds, then release it to select the function. Immediately after the following message displays, insert a scratch (blank) data cartridge that is not write-protected (or the tape drive exits maintenance mode). Test Head Load Scratch Tape After you insert the scratch data cartridge, the flashing C in the single-character display changes to H and one or more of the following messages display: Test Head Tape Loading Test Head Locating = = = > Test Head Rewinding = = = > followed by: Test Head Writing = = = > The tape drive runs the tests. v If no error is detected, the test will loop and begin again. To stop the loop, press the unload button for one second and release. When the loop ends, 0 temporarily appears in the single-character display. The drive rewinds the tape, unloads the cartridge, and displays the following message: Passed! Tape Unloading The drive then exits maintenance mode and displays the following message: Ultrium Tape Drive Drive Empty v If an error is detected the test stops, 5 appears in the single-character display, and the following message displays: ERROR! Drive/Media Error 80 IBM 3580 Ultrium Tape Drive Setup and Operator Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
4.
Press the unload button once per second until
H
appears in the single-character
display and the following message displays. (If you cycle past the desired code,
press the unload button once per second until the code redisplays.)
Maint Mode: Select
Test Head
5.
Press and hold the unload button for 3 or more seconds, then release it to select
the function. Immediately after the following message displays, insert a scratch
(blank) data cartridge that is not write-protected (or the tape drive exits
maintenance mode).
Test Head
Load Scratch Tape
After you insert the scratch data cartridge, the flashing
C
in the single-character
display changes to
H
and one or more of the following messages display:
Test Head
Tape Loading
Test Head
Locating
===>
Test Head
Rewinding
===>
followed by:
Test Head
Writing
===>
The tape drive runs the tests.
v
If no error is detected, the test will loop and begin again. To stop the loop,
press the unload button for one second and release. When the loop ends,
0
temporarily appears in the single-character display. The drive rewinds the
tape, unloads the cartridge, and displays the following message:
Passed!
Tape Unloading
The drive then exits maintenance mode and displays the following message:
Ultrium Tape Drive
Drive Empty
v
If an error is detected the test stops,
5
appears in the single-character display,
and the following message displays:
ERROR!
Drive/Media Error
80
IBM 3580 Ultrium Tape Drive Setup and Operator Guide