IBM 867431X Hardware Maintenance Manual - Page 17

Turning off the server, Stand-by mode

Get IBM 867431X - Eserver xSeries 330 PDF manuals and user guides View all IBM 867431X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

2 1 Turning off the server Turning off the server refers to the act of disconnecting the server from the power source. Complete the following steps to turn off the server: 1. Refer to your operating system documentation for the proper procedure to shut down the operating system. Note: Each operating system is different. Some will allow an immediate shut-down, while others require and orderly shut-down procedure. 2. Press the power control button on the front of the server. This will put the server in the stand-by mode. 3. Disconnect the server from the power source. Note: After turning off the server, wait at least 5 seconds before you turn on the server again. Stand-by mode Stand-by puts the server in a wait state. When in a wait state, the server is not running the operating system, and all core logic is shut down, except for the service processor. Complete the following steps to put the server into stand-by mode: 1. Refer to your operating system documentation for the proper procedure to shut-down the operating system. Note: Each operating system is different. Read all the documentation about shutting down the operating system before continuing. 2. Press the power control button on the front of the server. General information 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
1
2
Turning off the server
Turning off the server refers to the act of disconnecting the server from the power
source.
Complete the following steps to turn off the server:
1.
Refer to your operating system documentation for the proper procedure to shut
down the operating system.
Note:
Each operating system is different. Some will allow an immediate
shut-down, while others require and orderly shut-down procedure.
2.
Press the power control button on the front of the server. This will put the
server in the stand-by mode.
3.
Disconnect the server from the power source.
Note:
After turning off the server, wait at least 5 seconds before you turn on
the server again.
Stand-by mode
Stand-by puts the server in a wait state. When in a wait state, the server is not
running the operating system, and all core logic is shut down, except for the
service processor.
Complete the following steps to put the server into stand-by mode:
1.
Refer to your operating system documentation for the proper procedure to
shut-down the operating system.
Note:
Each operating system is different. Read all the documentation about
shutting down the operating system before continuing.
2.
Press the power control button on the front of the server.
General information
9