IBM 867431X Hardware Maintenance Manual - Page 64

The IBM Remote Supervisor Adapter, Installation prerequisites

Get IBM 867431X - Eserver xSeries 330 PDF manuals and user guides View all IBM 867431X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

c. Press the adapter firmly into the riser-card connector. Attention: When you install an adapter, be sure the adapter is correctly seated in the riser-card connector before you turn on the computer. Improperly seated adapters might cause damage to the system board, the riser-card, or the adapter. d. Push down on the blue adapter retention latch until it clicks into place, securing the adapter. e. Replace the expansion slot clip by sliding it down until it latches into place and holds the adapter securely. 9. Connect the internal cables to the adapter. Attention: Route cables so that they do not block the flow of air from the fans. 10. Replace the cover on the computer; then, reinstall the computer in the rack and connect all external cables. For more information see "Installing the cover" on page 93 for instructions. 11. Turn on the computer. The IBM Remote Supervisor Adapter The IBM Remote Supervisor Adapter can be installed in the xSeries 330. To update the Advanced System Managment (ASM) firmware or configure the ASM processor, you must download the image of the xSeries 330/IntelliStation R Pro Advanced System Management Firmware Update Utility program from the IBM Support page at http://www.ibm.com/pc/support on the World Wide Web. See "Advanced System Management" on page 36. Installation prerequisites Before installing the Remote Supervisor Adapter, perform the following tasks: v Obtain the most recent device drivers, Advanced System Management (ASM) firmware, DOS configuration utility, and management information base (MIB) from the IBM Support Web site, http://www.ibm.com/pc/support. See "Advanced System Management" on page 36. v Install the operating system on your server before you install the Advanced System Management device drivers. To install the operating system using ServerGuide, use only ServerGuide version 6.0.3, or later. Note: If you previously installed the operating system with ServerGuide version 6.0.2, make sure that you install the Advanced System Management device drivers from the IBM Remote Supervisor Adapter Support CD, or download the device drivers from the IBM Support Web site, http://www.ibm.com/pc/support. Do not install the device drivers from the directory that ServerGuide 6.0.2 created on the hard disk during its installation of the operating system. For information about installing the device drivers, see "Installing the Remote Supervisor Adapter" on page 62. v Update the basic input/output system (BIOS) code on your xSeries 330 server. The latest level of BIOS code for your server is available from the IBM Support Web site, http://www.ibm.com/pc/support. For information about how to update the BIOS code, see the documentation that comes with your xSeries 330 server. v If you are planning to configure Simple Network Management Protocol (SNMP) trap alerts on the Remote Supervisor Adapter, you must install and compile the management information base (MIB) on your SNMP manager. If you do not 56 Hardware Maintenance Manual: xSeries 330 Type 8674, IntelliStation R Pro Type 6851, and Network Equipment Building System Type 8674

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
c.
Press the adapter
firmly
into the riser-card connector.
Attention:
When you install an adapter, be sure the adapter is correctly
seated in the riser-card connector before you turn on the computer.
Improperly seated adapters might cause damage to the system board, the
riser-card, or the adapter.
d.
Push down on the blue adapter retention latch until it clicks into place,
securing the adapter.
e.
Replace the expansion slot clip by sliding it down until it latches into place
and holds the adapter securely.
9.
Connect the internal cables to the adapter.
Attention:
Route cables so that they do not block the flow of air from the
fans.
10.
Replace the cover on the computer; then, reinstall the computer in the rack
and connect all external cables. For more information see
“
Installing the
cover
”
on page 93 for instructions.
11.
Turn on the computer.
The IBM Remote Supervisor Adapter
The IBM Remote Supervisor Adapter can be installed in the xSeries 330. To update
the Advanced System Managment (ASM) firmware or configure the ASM
processor, you must download the image of the xSeries 330/IntelliStation R Pro
Advanced System Management Firmware Update Utility program from the IBM
Support page at http://www.ibm.com/pc/support on the World Wide Web. See
“
Advanced System Management
”
on page 36.
Installation prerequisites
Before installing the Remote Supervisor Adapter, perform the following tasks:
v
Obtain the most recent device drivers, Advanced System Management (ASM)
firmware, DOS configuration utility, and management information base (MIB)
from the IBM Support Web site, http://www.ibm.com/pc/support. See
“
Advanced System Management
”
on page 36.
v
Install the operating system on your server before you install the Advanced
System Management device drivers. To install the operating system using
ServerGuide, use only ServerGuide version 6.0.3, or later.
Note:
If you previously installed the operating system with ServerGuide version
6.0.2, make sure that you install the Advanced System Management
device drivers from the
IBM Remote Supervisor Adapter Support
CD, or
download the device drivers from the IBM Support Web site,
http://www.ibm.com/pc/support. Do not install the device drivers from
the directory that ServerGuide 6.0.2 created on the hard disk during its
installation of the operating system. For information about installing the
device drivers, see
“
Installing the Remote Supervisor Adapter
”
on
page 62.
v
Update the basic input/output system (BIOS) code on your xSeries 330 server.
The latest level of BIOS code for your server is available from the IBM Support
Web site, http://www.ibm.com/pc/support. For information about how to
update the BIOS code, see the documentation that comes with your xSeries 330
server.
v
If you are planning to configure Simple Network Management Protocol (SNMP)
trap alerts on the Remote Supervisor Adapter, you must install and compile the
management information base (MIB) on your SNMP manager. If you do not
56
Hardware Maintenance Manual: xSeries 330 Type 8674, IntelliStation R Pro Type 6851, and Network Equipment Building
System Type 8674