Home » IBM Manuals » Desktops » IBM 867431X » Manual Viewer

IBM 867431X Hardware Maintenance Manual - Page 37

System Service Processor Settings, Date and Time, System Security, Power-on Password

Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

- The default setting is Enable for all the controllers. If you select Disable, the system will not configure the disabled device and the operating system will not see the device. (This is equivalent to unplugging the device.) - If the on-board SCSI controller is disabled and no other storage device is installed, operating system startup cannot occur. Select System Service Processor Settings to view the interrupt-request setting (IRQ) used by the Advanced System Management Processor (system service processor). You can then use the arrow keys to select a new IRQ setting for the Advanced System Management Processor from the list of available choices. v Date and Time Select this choice to set the system date and time and to change the system time sent to the Advanced System Management Processor (service processor) when the server/workstation is started. This choice appears only on the full Configuration/Setup Utility main menu. The system time is in a 24-hour format: hour:minute:second. You can set a time delta to be added or subtracted from the system time that is sent to the service processor (Advanced System Management Processor) each time the server/workstation is started. Use the number keys to enter the hours and minutes and + or − to add or subtract from the system time. If you want the system clock time to be the same as the Advanced System Management Processor clock time, leave the value set at its default of 0. v System Security Select this choice to set passwords or a system owner's name. This choice appears only on the full Configuration/Setup Utility main menu. You can implement two levels of password protection: - Power-on Password Select this choice to set or change a power-on password. See "Using passwords" on page 31 for more information. - Administrator Password Select this choice to set or change an administrator password. Attention: If an administrator password is set and then forgotten, it cannot be overridden or removed. You must replace the system board. The administrator password provides access to all choices on the Configuration/Setup Utility main menu. You can set, change, or delete both the administrator and power-on passwords, and allow a power-on password to be changed by the user. See"Using passwords" on page 31 for more information. v Start Options Select this choice to view or change the start options. This choice appears only on the full Configuration/Setup Utility main menu. Start options take effect when you start the server/workstation. You can select keyboard operating characteristics, such as the keyboard speed. You also can specify whether the keyboard number lock starts on or off. You also can enable the server/workstation to run without a diskette drive, monitor, or keyboard. The server/workstation uses a startup sequence to determine the device from which the operating system loads. For example, you can define a startup sequence that checks for a startable diskette in the diskette drive, then checks the hard disk drive in bay 1, and then checks a network adapter. Configuration 29

Section	Page
About this manual	5
Important safety information	5
Online support	6
Contents	7
General checkout	9
General information	11
Features and specifications	12
What the xSeries 330 / IntelliStation R Pro offers	13
Reliability, availability, and serviceability features	13
Server controls and indicators	14
Front view	14
Rear view	15
Turning on the server	16
Turning off the server	17
Stand-by mode	17
Diagnostics	19
Diagnostic tools overview	19
POST	20
POST error messages	20
Event/error logs	20
Small computer system interface messages	20
Identifying problems using status LEDs	21
Light Path Diagnostics	21
Diagnostics panel	22
Diagnostic programs and error messages	23
Text messages	23
Starting the diagnostic programs	24
Viewing the test log	24
Recovering BIOS	26
Troubleshooting the Ethernet controller	27
Network connection problems	27
Ethernet controller troubleshooting chart	27
Ethernet controller messages	28
NDIS 4.0 (Windows NT) driver messages	28
Power checkout	30
Replacing the battery	31
Temperature checkout	33
Configuration	35
Using the Configuration/Setup Utility program	35
Starting the Configuration/Setup Utility program	35
Choices available from the Configuration/Setup main menu	35
Using passwords	39
Power-on password	39
Setting the password override switch	39
Administrator password	40
Using the SCSISelect utility program	41
Starting the SCSISelect utility program	41
Choices available from the SCSISelect menu	42
Using the PXE boot agent utility program	42
Starting the PXE Boot Agent Utility program	43
PXE Boot Agent Utility menu choices	43
Advanced System Management	44
Updating the ASM firmware	44
ASM Firmware Update Utility diskette menu choices	45
Hardware Status and Information	45
Configuration Settings	45
Alert Settings	45
Dial In/Out Settings	45
General Settings	46
Modem Settings	46
Update System Management Firmware	46
Exit	46
Configuring the ASM processor	46
Installing options	49
Notices and statements used in this book	49
Major components of the xSeries 330	50
Major components of the R Pro computer	51
System board	52
System board options connectors	52
System board LEDs	53
Before you begin	53
System reliability considerations	54
Working inside a server/workstation with power on	54
Rack installation	54
Removing the cover	56
Working with adapters in the xSeries 330	57
Adapter considerations	57
Installing an adapter	58
Working with adapters in the R Pro	61
Adapter considerations	61
Removing an adapter	62
Installing an adapter	62
The IBM Remote Supervisor Adapter	64
Installation prerequisites	64
Installation requirements	65
Remote Supervisor Adapter features	65
About your documentation	66
System requirements	66
Starting the IBM Documentation Browser	67
Using the IBM Documentation Browser	67
Unpacking and verifying components	68
Inventory checklist	68
Remote Supervisor Adapter components	70
Installing the Remote Supervisor Adapter	70
Connecting the power-supply adapter	73
Connecting the LAN and serial port cables	74
Cabling the Ethernet LAN port	75
Cabling the serial (COM) port	76
Updating the Remote Supervisor Adapter firmware	76
Configuring your system to enable remote access to the Remote Supervisor Adapter	79
Configuring the Ethernet settings	79
Configuring the serial port	81
Setting up point-to-point protocol	82
Completing the installation	84
Planning and cabling your interconnect network	85
Forwarding alerts	85
Cabling for the ASM interconnect network	86
Installing the ASM Interconnect module on the xSeries 330	87
ASM interconnect network configuration examples	88
Hard disk drives	90
Preinstallation steps	91
Installing or replacing a hard disk drive	91
Memory	92
Installing memory modules	93
Microprocessor	95
Installing the microprocessor	96
Removing a microprocessor	98
Fan assembly replacement	100
Installing the cover	101
I/O connector locations and ports in the R Pro	102
Input/Output ports	102
Console ports	103
Device breakout cable	103
Keyboard connector	103
Auxiliary-device (pointing device) connector	103
Using the computer as a remote console	104
Serial port	104
Viewing or changing the serial-port assignments	104
Serial-port connector	105
Universal Serial Bus ports	105
USB cables and hubs	105
USB-port connectors	106
Ethernet ports	106
Configuring the Ethernet controllers	106
Failover for redundant Ethernet	106
High Performance Ethernet Modes	107
Ethernet port connector	109
Advanced System Management ports	109
Audio ports	110
Video ports	110
I/O connector locations and ports on the xSeries 330	110
Input/Output ports	111
Serial port	111
Viewing or changing the serial-port assignments	111
Serial-port connector	111
Universal Serial Bus ports	112
USB cables and hubs	112
USB-port connectors	112
Ethernet ports	112
Configuring the Ethernet controller	113
Failover for redundant Ethernet	113
High Performance Ethernet Modes	113
Ethernet port connector	115
Advanced System Management ports	116
Working with cables	116
Cabling the RS-485 connectors	117
Connecting servers with a C2T chain	118
Testing the C2T chain	119
Using C2T	120
Cable management	120
FRU information (service only)	121
Diskette/CD-ROM drives	121
Diskette/CD-ROM drive bracket	122
Hard disk drive backplane	123
Power supply	123
PCI riser card	124
System board	124
Important Instructions for the IntelliStation R Pro (Type 6851)	125
Initializing the system board	125
Symptom-to-FRU index	127
Beep symptoms	127
No Beep symptoms	129
Information panel system error LED	129
Diagnostic error codes	130
Error symptoms	133
POST error codes	135
SCSI error codes	139
Temperature error messages	139
Fan error messages	140
System shutdown	140
Voltage related system shutdown	140
Temperature related system shutdown	141
DASD checkout	141
Bus fault messages	141
Undetermined problems	142
Parts listing, xSeries 330	145
System	146
Keyboards	148
Power cords	149
IntelliStation R Pro	150
Keyboards	152
Power cords	152
Related service information	155
Safety information	155
General safety	155
Electrical safety	156
Safety inspection guide	157
Handling electrostatic discharge-sensitive devices	158
Grounding requirements	159
Safety notices (multi-lingual translations)	159
Send us your comments!	188
Problem determination tips	189
Notices	189

Match case Limit results 1 per page

–

The default setting is Enable for all the controllers. If you select Disable, the

system will not configure the disabled device and the operating system will

not see the device. (This is equivalent to unplugging the device.)

–

If the on-board SCSI controller is disabled and no other storage device is

installed, operating system startup cannot occur.

Select

System Service Processor Settings

to view the interrupt-request setting

(IRQ) used by the Advanced System Management Processor (system service

processor). You can then use the arrow keys to select a new IRQ setting for the

Advanced System Management Processor from the list of available choices.

Date and Time

Select this choice to set the system date and time and to change the system time

sent to the Advanced System Management Processor (service processor) when

the server/workstation is started. This choice appears only on the full

Configuration/Setup Utility main menu.

The system time is in a 24-hour format: hour:minute:second.

You can set a time delta to be added or subtracted from the system time that is

sent to the service processor (Advanced System Management Processor) each

time the server/workstation is started. Use the number keys to enter the hours

and minutes and + or ± to add or subtract from the system time. If you want

the system clock time to be the same as the Advanced System Management

Processor clock time, leave the value set at its default of 0.

System Security

Select this choice to set passwords or a system owner’s name. This choice

appears only on the full Configuration/Setup Utility main menu.

You can implement two levels of password protection:

–

Power-on Password

Select this choice to set or change a power-on password. See “Using

passwords” on page 31 for more information.

–

Administrator Password

Select this choice to set or change an administrator password.

Attention:

If an administrator password is set and then forgotten, it cannot be

overridden or removed. You must replace the system board.

The administrator password provides access to all choices on the

Configuration/Setup Utility main menu. You can set, change, or delete both

the administrator and power-on passwords, and allow a power-on password

to be changed by the user.

See“Using passwords” on page 31 for more information.

Start Options

Select this choice to view or change the start options. This choice appears only

on the full Configuration/Setup Utility main menu. Start options take effect

when you start the server/workstation.

You can select keyboard operating characteristics, such as the keyboard speed.

You also can specify whether the keyboard number lock starts on or off. You

also can enable the server/workstation to run without a diskette drive, monitor,

or keyboard.

The server/workstation uses a startup sequence to determine the device from

which the operating system loads. For example, you can define a startup

sequence that checks for a startable diskette in the diskette drive, then checks

the hard disk drive in bay 1, and then checks a network adapter.

Configuration