Intel SR1530HCLRNA User Guide - Page 112

Removing System Blower from Blower Bracket SR1530CL, SR1530CLR

Get Intel SR1530HCLRNA - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858197274
View all Intel SR1530HCLRNA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

7. Turn the bracket over and remove the two screws that attach the failed blower to the blower bracket. Save these screws. You will reinstall them later. See letter "A" in the following figure). Lift the blower from the bracket (see letter "B"). B A AF000992 Figure 89. Removing System Blower from Blower Bracket (SR1530CL/ SR1530CLR) 8. Install the replacement blower onto the blower bracket, using the two screws you removed previously. 9. Set the blower assembly into the system. Insert the rear edge first and push the assembly slightly rearward to clear the hard disk drive brackets. Use caution to make sure you do not pinch any cables. 10. Route the cable from the blower at the right around the right side of the assembly and under the clip at the front of the blower bracket. 11. Secure the blower assembly to the system using the two screws you removed previously. 90 Server System User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
90
Server System User Guide
7.
Turn the bracket over and remove the two screws that attach the failed blower to the
blower bracket. Save these screws. You will reinstall them later. See letter “A” in
the following figure). Lift the blower from the bracket (see letter “B”).
Figure 89. Removing System Blower from Blower Bracket (SR1530CL/
SR1530CLR)
8.
Install the replacement blower onto the blower bracket, using the two screws you
removed previously.
9.
Set the blower assembly into the system. Insert the rear edge first and push the
assembly slightly rearward to clear the hard disk drive brackets. Use caution to
make sure you do not pinch any cables.
10.
Route the cable from the blower at the right around the right side of the assembly
and under the clip at the front of the blower bracket.
11.
Secure the blower assembly to the system using the two screws you removed
previously.
AF000992
A
B