Intel SR1530HCLRNA User Guide - Page 73

Installing or Removing a Slimline Optical Drive

Get Intel SR1530HCLRNA - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858197274
View all Intel SR1530HCLRNA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

7. With the black lever in the fully open position, slide the drive carrier into the server system. The green latch must be to the right. Do not push on the black lever until the lever begins to close by itself. Note: For proper airflow, the hard drive carrier must be replaced in the server system even if no hard drive is installed in it. 8. When the black lever begins to close by itself, push on it to lock the drive carrier into place. 9. Install the server system cover. For instructions, see "Installing the Server System Cover" on page 30. 10. (Optional) Install the front bezel. For instructions, see "Installing the Front Bezel" on page 27. 11. Plug all peripheral devices and the AC power cable(s) into the server. Installing or Removing a Slimline Optical Drive Caution: The optical drive is NOT hot-swappable. Before removing or replacing the optical drive, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and unplug the AC power cord from the system or wall outlet. Note: Slimline optical drive installations and removal instructions differ between the different server systems. Be sure to follow the instructions that correspond to your server system. Installing a Slimline Optical Drive (SR1530CL/SR1530CLR) Note: If you are replacing an optical drive, see "Removing a Slimline Optical Drive (SR1530CL/SR1530CLR)" on page 58 for instructions first. Return to these steps when directed. Note: The hardware necessary to install your optical drive was shipped to you in a bag labeled "CD-ROM Assy". 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information" on page iii. 2. Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the server system cover. For instructions, see "Removing the Server System Cover" on page 28. 4. Remove the bezel if it is installed. For instructions, see "Removing the Front Bezel" on page 26. Server System User Guide 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Server System User Guide
51
7.
With the black lever in the fully open position, slide the drive carrier into the server
system. The green latch must be to the right. Do not push on the black lever until
the lever begins to close by itself.
Note:
For proper airflow, the hard drive carrier must be replaced in the server
system even if no hard drive is installed in it.
8.
When the black lever begins to close by itself, push on it to lock the drive carrier
into place.
9.
Install the server system cover. For instructions, see
“Installing the Server System
Cover” on page 30
.
10.
(Optional) Install the front bezel. For instructions, see
“Installing the Front Bezel”
on page 27
.
11.
Plug all peripheral devices and the AC power cable(s) into the server.
Installing or Removing a Slimline Optical Drive
Caution:
The optical drive is NOT hot-swappable. Before removing or replacing the optical drive,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
Note:
Slimline optical drive installations and removal instructions differ between the different
server systems. Be sure to follow the instructions that correspond to your server system.
Installing a Slimline Optical Drive (SR1530CL/SR1530CLR)
Note:
If you are replacing an optical drive, see
“Removing a Slimline Optical Drive
(SR1530CL/SR1530CLR)” on page 58
for instructions first. Return to these steps when
directed.
Note:
The hardware necessary to install your optical drive was shipped to you in a bag labeled
“CD-ROM Assy”.
1.
Observe the safety and ESD precautions at the beginning of this book. See
“Safety
Information” on page iii
.
2.
Power down the server and unplug all peripheral devices and the AC power cable.
3.
Remove the server system cover. For instructions, see
“Removing the Server
System Cover” on page 28
.
4.
Remove the bezel if it is installed. For instructions, see
“Removing the Front
Bezel” on page 26
.