Intermec PM4i PM4i Mid-Range Printer User's Manual - Page 119

Adjusting the Label Taken Sensor, SETUP, PRINT DEFS, TEST/SERVICE - test feed needed

Get Intermec PM4i PDF manuals and user guides View all Intermec PM4i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

Chapter 4 - Troubleshooting and Maintaining the Printer Adjusting the Label Taken Sensor If you are using the optional label taken sensor (LTS), you may need to adjust the sensitivity depending on ambient light conditions and the reflective characteristics of the back side of the media. To adjust the LTS 1 Press T to enter the Setup menu, and use the keypad to go to the LTS menu: • If you are running Fingerprint, go to SETUP > PRINT DEFS > LTS. • If you are running IPL, go to SETUP > TEST/SERVICE > LTS. 2 Modify one or more LTS settings. Setting LTS Adjust LTS Test LTS Value How to Modify 1 Press E. The printer feeds a label. 2 Remove the label and press E again. The printer displays the sensitivity value that is automatically selected by the firmware and the range in which the LTS will work. 3 Press E again to proceed to the LTS Test menu. 1 Press E. The printer feeds a label. 2 Remove the label. The printer automatically feeds another label. 3 Repeat Steps 1 and 2 until you are sure the LTS is working properly. 4 Press E to stop the test and exit. 1 Press E. 2 Enter a new LTS value within the range indicated in the LTS Adjust menu (0 to 10). PM4i Mid-Range Printer User's Manual 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Chapter 4 — Troubleshooting and Maintaining the Printer
PM4i Mid-Range Printer User’s Manual
105
Adjusting the Label Taken Sensor
If you are using the optional label taken sensor (LTS), you may need
to adjust the sensitivity depending on ambient light conditions and
the reflective characteristics of the back side of the media.
To adjust the LTS
1
Press
T
to enter the Setup menu, and use the keypad to go to the
LTS menu:
•
If you are running Fingerprint, go to
SETUP
>
PRINT DEFS
>
LTS
.
•
If you are running IPL, go to
SETUP
>
TEST/SERVICE
>
LTS
.
2
Modify one or more LTS settings.
Setting
How to Modify
LTS Adjust
1
Press
E
. The printer feeds a label.
2
Remove the label and press
E
again. The printer
displays the sensitivity value that is automatically
selected by the firmware and the range in which the
LTS will work.
3
Press
E
again to proceed to the LTS Test menu.
LTS Test
1
Press
E
. The printer feeds a label.
2
Remove the label. The printer automatically feeds
another label.
3
Repeat Steps 1 and 2 until you are sure the LTS is
working properly.
4
Press
E
to stop the test and exit.
LTS Value
1
Press
E
.
2
Enter a new LTS value within the range indicated in
the LTS Adjust menu (0 to 10).