Invacare SOLARA3G Owners Manual - Page 84

Wheels/Forks

Get Invacare SOLARA3G PDF manuals and user guides View all Invacare SOLARA3G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

12 WHEELS/FORKS 12 Wheels/Forks ƽ WARNING After any adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely otherwise injury or damage may occur. 12.1 Installing/Removing Rear Wheels 1. Quick-Release  To remove rear wheels, reverse this procedure. 1. Push in the detent pin of the quick-release axle and insert the quick-release axle through the center of the rear wheel. 2. Push in the tip of the quick-release axle again and insert the axle (with wheel) into the axle mounting plate on the side of the wheelchair frame until the assembly locks in place. ƽ WARNING Make sure detent pin and locking pins of the quick-release axles are fully released before operating the wheelchair. The locking pins MUST be protruding past the inside of the axle mounting plate for a positive lock. Keep locking pins clean. 3. Ensure quick release axle locking pins are properly engaged and secure in the axle mounting plate by pulling the rear wheel away from the wheelchair frame. If the locking pins do not engage or there is too much movement of the rear wheel assembly in a back and forth position. Refer to Adjusting The Quick-Release Axle on page 86. 4. Repeat STEPS 1-3 for other rear wheel assembly. Invacare® Solara®3G/Spree 3G Wheelchair 84 Part No 1154295

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
12
WHEELS/FORKS
Invacare® Solara®3G/Spree 3G Wheelchair
84
Part No 1154295
12 Wheels/Forks
12.1
Installing/Removing Rear Wheels
1.
Quick-Release
1.
Push in the detent pin of the quick-release axle and insert the quick-release axle through the center of the rear wheel.
2.
Push in the tip of the quick-release axle again and insert the axle (with wheel) into the axle mounting plate on the side of the wheelchair frame
until the assembly locks in place.
3.
Ensure quick release axle locking pins are properly engaged and secure in the axle mounting plate by pulling the rear wheel away from the
wheelchair frame. If the locking pins do not engage or there is too much movement of the rear wheel assembly in a back and forth position. Refer
to Adjusting The Quick-Release Axle
on page 86.
4.
Repeat STEPS 1-3 for other rear wheel assembly.
±
WARNING
After any adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely -
otherwise injury or damage may occur.
To remove rear wheels, reverse this procedure.
±
WARNING
Make sure detent pin and locking pins of the quick-release axles are fully released before operating the wheelchair.
The locking pins MUST be protruding past the inside of the axle mounting plate for a positive lock.
Keep locking pins clean.