Kenmore HE2t User Guide - Page 42

Removing The Central Control Unit - ccu

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

REMOVING THE CENTRAL CONTROL UNIT Central Control Unit Connectors (12) Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Remove the top cover from the washer (see page 4-2 for the procedure). Wire Clamps 6. Pry up on the locking tab, and push the central control unit (CCU) toward the rear of the washer as far as it will go, and remove the CCU tabs from the keyhole slots in the chassis. CCU Locking Tab Push Central Control Unit 4. Pull the wire connectors off the edges of the central control unit circuit board (see the top right photo). When you pull an edge connector off the board, first pry the locking tab away from the connector with a small screwdriver blade to release it. 5. Slide the hooked ends of the two wire clamps off the locking tabs, and remove the wires from the clamps. Keyhole Slots CCU Tabs 4-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
4-4
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.
REMOVING THE CENTRAL CONTROL UNIT
Central Control Unit
4.
Pull the wire connectors off the edges of
the central control unit circuit board (see
the top right photo). When you pull an
edge connector off the board, first pry the
locking tab away from the connector with
a small screwdriver blade to release it.
5.
Slide the hooked ends of the two wire
clamps off the locking tabs, and remove
the wires from the clamps.
Central Control Unit Connectors (12)
Wire Clamps
6.
Pry up on the locking tab, and push the
central control unit (CCU) toward the
rear of the washer as far as it will go, and
remove the CCU tabs from the keyhole
slots in the chassis.
Keyhole Slots
CCU Locking Tab
CCU Tabs
Push
1.
Unplug washer or disconnect power.
2.
Turn off the water supply to the washer.
3.
Remove the top cover from the washer
(see page 4-2 for the procedure).