Kenmore HE2t User Guide - Page 44

Removing The Water Inlet Valve

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

REMOVING THE WATER INLET VALVE Lift Locking Tab Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Remove the water hoses from the hot and cold water inlet valve. 4. Remove the top cover (see page 4-2 for the procedure). Water Inlet Valve Pull Connector Out Cold Water (Stripe) Solenoid Terminal Holder Water Inlet Valve Inlet Hose & Clamp 5. Lift the locking tabs with a small-blade screwdriver (see the top right photo), and pull the wire connectors out of the hot and cold water inlet valve solenoid terminal holders. NOTE: The cold water wire connector has a black stripe on it. 6. Loosen the clamp, and pull the water inlet hose off the water inlet valve. 7. At the rear of the washer, remove the screw from the water inlet valve. Slide the valve to the right, and push it into the washer off the rear panel. Water Inlet Valve Screw 4-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
4-6
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.
1.
Unplug washer or disconnect power.
2.
Turn off the water supply to the washer.
3.
Remove the water hoses from the hot
and cold water inlet valve.
4.
Remove the top cover (see page 4-2 for
the procedure).
REMOVING THE WATER INLET VALVE
Water Inlet Valve
5.
Lift the locking tabs with a small-blade
screwdriver (see the top right photo), and
pull the wire connectors out of the hot
and cold water inlet valve solenoid termi-
nal holders.
NOTE:
The cold water wire
connector has a black stripe on it.
6.
Loosen the clamp, and pull the water in-
let hose off the water inlet valve.
7.
At the rear of the washer, remove the
screw from the water inlet valve. Slide
the valve to the right, and push it into the
washer off the rear panel.
Water Inlet Valve Screw
Lift Locking Tab
Pull Connector
Out
Solenoid
Terminal Holder
Inlet Hose
& Clamp
Water Inlet Valve
Cold Water (Stripe)