Kenwood DNX690HD Instruction Manual - Page 52

Car type setup, DSP select, Audio Setting Up - bypass

Get Kenwood DNX690HD PDF manuals and user guides View all Kenwood DNX690HD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Return to the Top page Audio Setting Up Crossover network setup You can set a crossover frequency of speakers. 1 Touch the speaker to set the crossover in the Speaker Select screen. 2 Touch [X'over]. X'over screen appears. 3 Set each item as follows. Car type setup You can setup the car type and speaker network, etc. 1 Touch [Car Type] in the Audio SETUP screen. Car Type screen appears. 2 Select your car type from the list. TW (Tweeter) Gain *1 Adjusts the tweeter level. (When front is selected on Speaker Select screen) Gain Adjusts the front speaker, rear speaker, or subwoofer level. Phase*2 Sets the phase of subwoofer output. The phase is reversed 180 degrees when set to "Reverse". (When subwoofer is selected on Speaker Select screen) HPF FREQ High Pass Filter adjustment. (When front or rear speaker is selected on Speaker Select screen) LPF FREQ Low Pass Filter adjustment. (When subwoofer is selected on Speaker Select screen) Slope*3 Sets a crossover slope. *1 Only when "Tweeter" is set to "Small", "Middle", "Large" in . *2 Only when "Subwoofer" is set to a mode other than "None" in . *3 Only when "LPF FREQ"/"HPF FREQ" is set to a mode other than "Through" in

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
102
102
103
Return to the Top page
Audio Setting Up
Return to the Top page
Audio Setting Up
Crossover network setup
You can set a crossover frequency of
speakers.
1
Touch the speaker to set the crossover
in the Speaker Select screen.
2
Touch [X’over].
X’over screen appears.
3
Set each item as follows.
TW (Tweeter) Gain *
1
Adjusts the tweeter level. (When front is
selected on Speaker Select screen)
Gain
Adjusts the front speaker, rear speaker, or
subwoofer level.
Phase*
2
Sets the phase of subwoofer output.
The phase is reversed 180 degrees when set
to “Reverse”. (When subwoofer is selected on
Speaker Select screen)
HPF FREQ
High Pass Filter adjustment. (When front or rear
speaker is selected on Speaker Select screen)
LPF FREQ
Low Pass Filter adjustment. (When subwoofer
is selected on Speaker Select screen)
Slope*
3
Sets a crossover slope.
*
1
Only when “Tweeter” is set to “Small”,
“Middle”,“Large”in <Speaker Setup>.
*
2
Only when “Subwoofer” is set to a mode
other than “None” in <Speaker Setup>.
*
3
Only when “LPF FREQ”/“HPF FREQ” is set to
a mode other than “Through” in <X’over>.
Car type setup
You can setup the car type and speaker
network, etc.
1
Touch [Car Type] in the Audio SETUP
screen.
Car Type screen appears.
2
Select your car type from the list.
NOTE
•
If your car type is selected, the Delay Time
Alignment is set automatically (for timing
adjustment of sound output for each channel) to
have the highest surround effects.
Speaker location setup
1
In the Car Type screen, touch [Location].
Speaker Location screen appears.
2
Select the speaker locations using [
3
].
Front Speaker
Select the location from “Door”/ “On Dash”/
“Under Dash”.
Rear Speaker
Select the location from “Door”/ “Rear Deck”,
“2nd Row”/ “3rd Row” (Minivan, Minivan
(Long)).
DSP select
You can select whether using DSP (Digital
Signal Processor) System.
1
Touch [Bypass] or [Through] of [DSP
Select] in the Audio SETUP screen.
Bypass
There is no effect by DSP.
Through
There is an effect by DSP.
NOTE
•
When the mode is set to [Bypass], DSP System
cannot be adjusted.