Konica Minolta Fujitsu fi-6400 Operation Guide - Page 95

Replacing the Pick Roller

Get Konica Minolta Fujitsu fi-6400 PDF manuals and user guides View all Konica Minolta Fujitsu fi-6400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Chapter 6 Replacing Consumables 6.2 Replacing the Pick Roller There are two pick rollers. Make sure to replace both two units. 1 Remove all documents from the stacker. 2 Open the ADF. For information on how to open the ADF, refer to "1.5 Opening/ Closing the ADF" (page 19). Be careful not to have your fingers caught when the ADF closes. 3 Remove the pick rollers (×2) from the scanner. 1 Open the roller cover. Grab the tabs on the left and right side with your fingers and pull down the cover towards you. 2 Pull the pick roller off the rotating shaft as you grab the tab on the pick roller (×2). Pick Roller 4 Install a new set of pick rollers (×2) in the scanner. 1 Place the pick rollers (×2) on the shaft. TOP Contents Index Introduction Scanner Overview How to Load Documents How to Use the Operator Panel Various Ways to Scan Daily Care Replacing Consumables Troubleshooting Operational Settings Appendix Tab Roller Cover 2 Close the roller cover. Make sure that both ends of the cover are locked firmly. Glossary 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
Index
Chapter 6 Replacing Consumables
Appendix
Glossary
Introduction
Contents
TOP
95
How to Load
Documents
How to Use
the Operator
Panel
Various Ways
to Scan
Daily Care
Troubleshooting
Operational
Settings
Scanner
Overview
Replacing
Consumables
1
Remove all documents from the stacker.
2
Open the ADF.
For information on how to open the ADF, refer to
"1.5 Opening/
Closing the ADF" (page 19)
.
3
Remove the pick rollers (×2) from the scanner.
1
Open the roller cover. Grab the tabs on the left and right side with
your fingers and pull down the cover towards you.
2
Pull the pick roller off the rotating shaft as you grab the tab on the
pick roller (×2).
4
Install a new set of pick rollers (×2) in the scanner.
1
Place the pick rollers (×2) on the shaft.
2
Close the roller cover. Make sure that both ends of the cover are
locked firmly.
6.2 Replacing the Pick Roller
There are two pick rollers. Make sure to replace both two units.
Be careful not to have your fingers caught
when the ADF closes.
Tab
Roller Cover
Pick Roller