Kyocera FS-C5350DN FS-C5350DN Operation Guide (Advanced)
Kyocera FS-C5350DN Manual
 |
View all Kyocera FS-C5350DN manuals
Add to My Manuals
Save this manual to your list of manuals |
Kyocera FS-C5350DN manual content summary:
- Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 1
FS-C5350DN Advanced Operation Guide - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 2
- Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 3
Menu Selection System 2-8 Setting a Mode Selection Menu 2-10 Report Print 2-11 USB Memory (USB memory selection 2-17 Custom Box (Using a Custom Box 2-19 Job Box 2-23 Counter (Viewing the counter value 2-30 Paper Settings 2-31 Print Settings 2-39 Network (Network settings 2-48 Device Common - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 4
iv - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 5
INTRODUCTION This guide has the following chapters: 1 Handling Paper Explains how choose, handle and load paper. 2 Using the Operation Panel Explains how to use the operation panel to configure the printer. 3 Options Shows the available options. 4 Computer Interface Describes the possible - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 6
Braket Bold Note Important Caution Warning Conventions This manual uses the following conventions: Description Example Used to emphasize a key word, phrase or reference to additional information. To replace the toner container, refer to Toner Container Replacement on page 3-2. Used to denote - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 7
1 Handling Paper This chapter contains explanations on the following topics: General Guidelines Selecting the Right Paper Paper Type Loading Paper 1-2 1-4 1-13 1-14 Handling Paper 1-1 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 8
, poor print quality, and paper waste, and in extreme cases can damage your office by ensuring efficient, trouble-free printing and reducing wear printer cannot produce highquality results when the wrong paper is used. Low-priced paper is not economical in the long run if it causes printing problems - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 9
Maximum Paper Size 216 mm 8-1/2 inches 216 mm 8-1/2 inches Recommended Paper The following products are recommended for use with the printer for optimum performance. Size Letter, Legal A4 Product Hammermill LASER PRINT NEUSIEDLER COLOR COPY Weight 90 g/m² (24 lb) 90 g/m² Handling Paper 1-3 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 10
Selecting the Right Paper This section describes the guidelines for selecting paper. Condition Avoid using paper that is bent at the edges, curled, dirty, torn, embossed, or contaminated with lint, clay, or paper shreds. Use of paper in these conditions can lead to illegible printing and paper jams - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 11
heavy or too light may cause feed errors or paper jams as well as premature wear of the product. Uneven weight of paper, namely uneven paper thickness may cause multiple-sheet feeding or print quality problems such as blurring because of poor toner fusing. The recommended basis weight is: Cassette - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 12
having problems with paper jams, multiple feeds, and faint printing, the paper you are using may be too thin. If you are having problems with paper the paper's appearance, feed ability, curl, electrostatic properties, and toner fusing characteristics. The moisture content of the paper varies with - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 13
care to ensure that these problems do not occur. Packaging: correctly packaged. Note You might see the printer emitting steam in the area around the top for use with copiers or printers (heatfusing type). When using likely than white bond paper to give trouble during printing. No liability will be - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 14
Must tolerate at least 190 °C (374 °F) 0.100 to 0.110 mm (3.9 to 4.3 mils) Polyester ±0.7 mm (±0.0276 inches) 90° ±0.2° To prevent printing problems, feed transparencies into the printer one sheet at a time from the MP tray. Always load the transparencies vertically (with the long edge towards the - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 15
, adhesive-backed label paper is particularly likely to give printing problems. Adhesive label paper must be entirely covered by its top sheet spaces in between are liable to peel off, causing serious paper jam problems. Some label paper is manufactured with an extra margin of top sheet around - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 16
Grain on page 1-6. This direction can easily cause wrinkles and creases when envelopes pass through the printer. Before purchasing envelopes, make a test print to check whether the printer accepts the envelope. • Do not use envelopes that have an encapsulated liquid adhesive. • Avoid a long printing - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 17
bond paper except for whiteness, refer to Paper Specifications on page 1-2. Note Before purchasing recycled paper, test a sample on the machine and check that the printing quality is satisfactory. Coated Paper Coated paper is created by treating the surface of the base paper with a coating that - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 18
in very humid environments, ensure that the paper is kept dry as moisture may cause sheets to stick together when they are fed into the printer. Paper Type Indicators (Optional paper feeder PF-510) If you are going to load non standard paper in the optional paper feeder PF-510, cut - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 19
printing under the optimum setting for the type of paper being used. Setting the paper type for the paper source from the printer's operation panel will cause the printer to automatically select the paper source and print in the mode best suited to that type of paper. A different paper type setting - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 20
printing. Paper Cassette 2 Pull the paper cassette all the way out of the printer. Paper Size Dial 3 Turn the paper size dial so that the size of dial is set to Other the paper size must be set into the printer on the operation panel. Refer to Cassette (1 to 4) Size (Setting the cassette - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 21
. 6 Slide the paper into the paper cassette. Load Limit Note Do not load more paper than will fit under the load limits on the paper guides. The paper cassette will hold approximately 500 sheets of 80 g/m² (21 lb.) paper with a thickness of 0.11 mm. Handling Paper 1-15 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 22
7 Insert the paper cassette into the slot in the printer. Push it straight in as far as it will go. There is a paper gauge on the right side of the front of the paper cassette - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 23
guides and insert as far as it will go. Note Do not load more paper than will fit under the load limits on the inside of the MP tray. When printing on transparencies, feed the sheets into the Load Load printer print modes are imprinted on the switch. Check that the correct mode is selected for - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 24
Paper stopper Align the paper stopper to the desired paper size. • For A4 or Letter size paper : Align with position £. • For Legal size paper : Align with position ¤. 1-18 Handling Paper - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 25
Menu Selection System 2-8 Setting a Mode Selection Menu 2-10 Report Print 2-11 USB Memory (USB memory selection) 2-17 Custom Box (Using a Custom Box) 2-19 Job Box 2-23 Counter (Viewing the counter value) 2-30 Paper Settings 2-31 Print Settings 2-39 Network (Network settings) 2-48 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 26
Information This chapter provides the information you need to configure the Ecosys Color printer. In general you need to use the operation panel only to make default settings. You can make most changes to the printer settings using the printer driver through the application software. Note Changes to - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 27
. Message Display The message display on the operation panel shows: • Status information, the ten messages listed below which are displayed during normal operation. • Error codes, when the printer requires the operator's attention; as explained in the Operation Guide. Using the Operation Panel 2-3 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 28
details on Auto Sleep, refer to Sleep Timer (Sleep timer timeout time) on page 2-62. Jobs inside the printer are being canceled. To cancel a job, refer to Canceling a Printing Job on page 2-6. Error Codes Refer to the Troubleshooting section in the Operation Guide. 2-4 Using the Operation Panel - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 29
is being written to or read from a memory card or hard disk. Flashing. Indicates that the printer requires maintenance or is warming up. On. Indicates the occurrence of a problem or an error. For details, refer to the Troubleshooting section in the Operation Guide. Using the Operation Panel 2-5 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 30
's on-line and off-line states. You can temporarily stop the print job by switching the printer off-line. • Print and feed out one page when the printer displays Waiting. • Recover from certain errors. • Recover from Auto Sleep. Cancel Key This key is used to: • Cancel a printing job. • Stop the - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 31
• When Use alternative? is shown in the message display, use U and V key to select an alternative paper source. OK Key This key is used to: • Finalize settings of numeric values and other selections. • Set the paper source when Use alternative? is shown in the message display. Using the Operation - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 32
driver will take priority over settings made in the operation panel. Entering the Mode Selection Menu Press [MENU] when Ready is indicated on the printer message display. The mode selection menu is displayed. IMPORTANT The Custom Box option appears in the mode selection menu when the hard disk - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 33
Paper Settings > Selecting a Menu The mode selection menu is hierarchical. Press U or V to display the desired menu. If the selected menu has a sub-menu, > is displayed after the menu. Press Z to move to the sub-menu or Y to go back. Indicates that there is a sub-menu >Type Adjust > > is - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 34
Job Box • Counter • Paper Settings • Print Settings • Network • Device Common • Security • Job Accounting • Admin • Adjust/Maintenance Note If you use the mode first selected when the printer is turned on, Report Print is displayed. For the second and subsequent times, the last menu option - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 35
Print > appears. >Print Menu Map ? Note that menus shown in the list may vary depending on which optional units installed in the printer. Print Menu Map The printer prints a full list of the menu selection system menu map. 1 Press Z while Report Print > is displayed. 2 >Print Menu Map appears. In - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 36
Menu Map Sample Menu Map Printer FS-C5350DN Firmware version 2-12 Using the Operation Panel - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 37
Print Status Page You can check the printer's current status, including available memory Press [OK] again. The message Processing appears and the printer prints a status page. For a sample status page depending on the printer's firmware version. Status Page Printer FS-C5350DN Firmware version - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 38
as default when the printer is shipped from the factory. The emulations are: - PCL 6 - KPDL 8 Page Information This item shows the page related items: - Total printed page count - Total page count of each paper size 9 Consumable Status This item shows the approximate level of remaining toner. When - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 39
File List ? 4 Press [OK] again. The message Processing appears and the printer prints a list of fonts with a sample and font ID (number) for each the files on the RAM disk. IMPORTANT This is displayed when RAM disk mode is enabled. 1 Press Z while Report Print > is displayed. 2 Press U or V - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 40
to print a list of the files on a memory card. IMPORTANT This message will be displayed when the memory card installed in the printer. 1 Press Z while Report Print > is displayed. 2 Press U or V repeatedly until >Print Mem. Card File List appears. 3 Press [OK]. A question mark (?) appears. 4 Press - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 41
Memory are as follows: • Print File (Printing a file) • Copies (Number of copies) • Paper Source (Selecting the paper feed source) • Remove Device menus shown in the list may vary depending on which optional units installed in the printer. / /00:Folder 1 /00:Folder 1 /00:Folder 2 Print File ( - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 42
this feature, an optional hard disk must be installed in the printer or the RAM disk must be set to On. 1 While Copies in step 5 above is displayed, press U and V or Y and Z to display the number of copies. (E.g.: 10) Paper Source ? Cassette 1 Paper Source ? Cassette 2 >Remove Device ? 2 Press [OK - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 43
CENTER Operation Guide and KX Printer Driver User Guide. Use the printer's operation panel to print the print data stored in a Custom Box. The options available in Custom Box are as follows: • Select Box (Box number : Box name) (Selecting the Custom Box) • Print Box List (Prints a Custom Box list - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 44
2-20 Box Password _ Box Password (Box password input) User access to a Custom Box can be restricted by specifying a password for the box. The password is specified from the printer driver. 1 If you have set a password for the Custom Box, press Z while >Select Box > is displayed. Box Password is - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 45
or more of the following are displayed: MP tray Cassette (only the printer's standard cassette used) Cassette 1 to 4 (optional paper feeder installed) (?). >Select Box 0001:Box 1 6 Select Off or On using U or V. 7 Press [OK]. Processing is displayed and the specified number of copies of the - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 46
copies of all the documents are printed. If you selected On in the Delete Printed screen, all the documents are deleted after printing ends. Delete All Files (Deletes all the data) Use this procedure to delete all the documents in the Custom Box. > 1 Press U or V while >Select Box > and the box - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 47
the earlier ones to be deleted. Note Refer to the KX Printer Driver User Guide for the driver settings and print (save) procedures. The options available in Job Box are as follows: • Using Quick Copy/Proof-and-Hold Quick Copy (User Name) (Selecting the User) (User Name) (Data Name) (Selecting the - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 48
the required number of copies from the printer operation panel. To print a job as a quick copy job, refer to KX Printer Driver User Guide. The default number of print jobs that can be stored on the hard disk is 32. This value can be increased to up to 50 from the Job Box Configuration menu. For - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 49
>Quick Copy ?Harold >Quick Copy ?Arlen >Arlen ?Report >Report Copies 001 >Report Copies 001 >Report Delete Printing Additional Copies using Quick Copy 1 Press Z while Job Box > is displayed. 2 Press U or V repeatedly until >Quick Copy appears. The name entered in the printer driver (Harold, - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 50
will be deleted. Note Refer to KX Printer Driver User Guide for the driver settings. >Quick Copy ?Harold >Quick Copy ?Arlen >Arlen ?Report >Report Copies 001 >Report Copies 001 Printing Remaining Copies of a Proof-and-Hold Job 1 Press Z while Job Box > is displayed. 2 Press U or V repeatedly - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 51
printing. Refer to KX Printer Driver User Guide for the driver settings. Releasing a Private/Stored Job 1 Press Z while Job Box > is displayed. >Agenda ID >Agenda Copies 0000 001 7 Press [OK]. The ID input line appears. Enter the four-digit access code entered in the printer driver and press [OK]. - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 52
example), press [OK]. Enter the four-digit access code entered in the printer driver and press [OK]. 3 Press V repeatedly until Delete appears for the number of copies. 4 Press [OK]. The private job is deleted. Job Box Configuration Change Job Box settings, such as the maximum number of storable - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 53
MENU]. The display returns to Ready. Set Automatic Delete times for Temporary Jobs 1 Press Z while Job Box > is displayed. 2 Press U or V repeatedly until >Job Box Configuration > appears. 3 Press Z. 4 Press U or V repeatedly until >>Delete appears. 5 Press [OK]. A blinking question mark (?) appears - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 54
Counter Counter (Viewing the counter value) Displays the number of pages printed. The options available in Counter are as follows: • Printed Pages (Displaying the total printed pages) • Color (Displaying the color printed pages) • Monochrome (Displaying the monochrome printed pages) 1 Press [ - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 55
is used to format the job to print. If the sizes do not match, printing will not be performed on the correct size paper. The default setting is Letter size for the U.S. and Canada and A4 for other countries. For more information about the paper sizes that you can feed from - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 56
set the paper type that can be supplied from the MP tray. The default setting is PLAIN. For more information about paper types that you can feed 8) Note You can define any paper type and store that definition in the printer. For more information, refer to Type Adjust (Creating custom paper type) on - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 57
cassette out of the printer and set the paper size using the paper size dial. A4 Paper Size Dial 2 Adjust the paper guides in the cassette to on page 1-14). Selecting the Size Dial Setting 1 Pull the cassette out of the printer and set the paper size dial to Other. For details, refer to step 1 in - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 58
until >>Unit appears. The unit of measurement can be selected between millimeters and inches. The current unit of measurement is displayed (the default setting is mm). 3 Press [OK]. A blinking question mark (?) appears. 4 Select mm or inch using U or V. 5 Press [OK]. Set the dimensions of the - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 59
Entering the Width and Length Enter the paper size for X Dimension and Y Dimension as shown in the figure. Y Dimension 148 to 356 mm (5.83 to 14.02 inches) 105 to 216 mm (4.13 to 8.5 inches) X Dimension >>X Dimension 216 mm 1 When the unit of measurement is set, press V. >>X Dimension appears ( - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 60
, etc.) for the paper cassette, you can automatically select the paper in the paper cassette according to the paper type you command on the printer driver. The default setting is plain paper for all paper cassettes. If the PF-500 or PF-510 optional paper feeder is installed, use the same procedure - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 61
Type Adjust (Creating custom paper type) The following describes the procedure used to set a user-defined paper type for the printer. Eight custom user settings may be registered. After having been set, any of these may be called up when setting the paper type for a paper - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 62
2-37) and press Z. 2 Press U or V repeatedly until >>Duplex Path appears. 3 Press [OK]. A blinking question mark (?) appears. 4 Select Enable or Disable using U or V. For details of the default setting for each paper type, refer to Paper Specifications on page 1-2. 5 Press [OK]. 6 Press [MENU]. The - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 63
or Fine), the gloss mode (Low or High), the number of copies, reduced printing and the page orientation. The options available in Print source, from which the printer feeds paper as the default. If an optional paper feeder(s) is installed, it is also available for the default paper source. 1 Press - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 64
has been chosen. If Auto is selected, the printer searches for a paper feed source that matches the paper size and type, and paper is delivered from that source. An error message is displayed if Fixed is selected, but a match is not found. The default setting is Auto. To change the settings, follow - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 65
(Duplex printing) Using the duplexer, you can automatically print on both sides of the paper. The duplexer is mounted underneath the printer. Duplex printing is available for the following paper types: PLAIN PREPRINTED BOND RECYCLED ROUGH LETTERHEAD COLOR PREPUNCHED HIGH QUALITY Activating the - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 66
the desired binding mode. The message display toggles through the following: Off (default) Short edge bind Long edge bind 5 Press [OK]. 6 Press [MENU operation panel, the printer ignores the difference between A4 and Letter paper sizes. Printing is performed without an error message even if the - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 67
[OK]. 6 Press [MENU]. The display returns to Ready. Error Report (Printing KPDL errors) The printer can print error descriptions when printing error occurs during KPDL emulation. The default is On - the printer does not print KPDL errors. 1 Press Z while Print Settings > is displayed. 2 Press U or - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 68
color or monochrome printing) You can use the Color Mode menu on the operation panel to select the Monochrome or Color printing mode. By default, the printer is set to print in color mode. 1 Press Z while Print Settings > is displayed. 2 Press U or V repeatedly until >Color Mode appears. 3 Press [OK - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 69
Selecting the EcoPrint mode) By enabling EcoPrint mode, you can minimize the amount of toner used during printing. Because images or V repeatedly until >Page Set > appears. >>Copies 001 Copies (Number of copies) You can set the number of copies of each page to be printed for the current interface - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 70
6 Press [MENU]. The display returns to Ready. Orientation (Print orientation) You can select portrait (upright) or landscape (sideways) page orientation. Portrait Orientation Landscape Orientation A A >>Orientation ? Portrait >>Wide A4 ? Off 1 Press Z while >Page Set > is displayed. 2 Press U - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 71
TIFF/JPEG Size ? Paper Size TIFF/JPEG Size (Print mode setting for TIFF/JPEG files) Sets the print mode for TIFF/JPEG files. The default setting is Paper Size. 1 Press Z while >Page Set > is displayed. 2 Press U or V repeatedly until >>TIFF/JPEG Size appears. 3 Press [OK]. A blinking question mark - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 72
printer supports TCP/IP and TCP/IP (IPv6) protocols. IP is an abbreviation for Internet Protocol. This printer /IP (IPv6) (IPv6 settings) Note Check with your network administrator when selecting the options for TCP/IP are displayed when TCP/IP is enabled. 1 Press Z while Network > is displayed. 2 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 73
a network connection when a host attempts to connect to the network (Internet). This information includes the IP address of the local node and the default router (the router in the host's own network system) and the DNS (Domain Name System) server. DHCP is an extension of the BOOTP (Bootstrap - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 74
2-50 Subnet Mask (Subnet mask setting) The subnet mask is a way of augmenting the network address section of an IP address. A subnet mask represents all network address sections as 1 and all host address sections as 0. The number of bits in the prefix indicates the length of the network address. - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 75
by UDP port 5353. If a firewall is enabled, the user must check that UDP port 5353 is left open so Bonjour packets are accepted. If you install Bonjour on Windows XP Service Pack 2 or later, the Windows firewall will be set up address space, which resolves the problem of the lack of addresses under - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 76
MENU]. The display returns to Ready. DHCPv6 (DHCPv6 setting) DHCPv6 is the next-generation of the Internet's Dynamic Host Configuration Protocol and supports IPv6. It extends the BOOTP startup protocol that defines the protocols used for transferring configuration information to hosts on the network - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 77
the functions in this printer. The options available in Card (Using the memory card) • Error Handling (Error detection setting) • Timer (Timer setting) service technician for information. 1 Press Z while Device Common > is displayed. 2 Press U or V repeatedly until >MSG Language appears. The default - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 78
printer is located some distance from the user. The options available in Buzzer are as follows: • Key Confirm. (Key confirmation tone setting) • Job End (Job completed tone setting) • Ready (Preparation completed tone setting) • Error (Error sounds when printing ends. The default setting is Off. 1 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 79
V. 5 Press [OK]. 6 Press [MENU]. The display returns to Ready. Error (Error tone setting) When On is selected in this setting, a tone sounds when a problem such as running out of paper or a paper jam occurs during printing. The default setting is On. 1 Press Z while >Buzzer > is displayed. 2 Press - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 80
printer memory that can temporarily store print jobs. The stored print job can then be used to print multiple copies on the RAM disk. Note The printer supports three types of storage device; memory card, some Job Box functions to be used. The RAM disk is allocated from the printer memory available - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 81
before use. This menu is displayed only when the optional hard disk is installed on the printer. Note If the optional hard disk is installed in the printer, the Custom Box and Job Box will be available. >Hard Disk 1 Press Z while Device Common > is displayed. > 2 Press U or V repeatedly until - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 82
including a used hard disk. Formatting of the hard disk must be executed from the printer. Use the procedure below to format the hard disk. When a new hard disk is inserted in the printer's slot, Format error Hard disk will appear on the message display. 1 Press Z while >Hard Disk > is displayed - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 83
on a storage device including a used memory card. Formatting of the memory card must be executed from the printer. When a new memory card is inserted in the printer's slot, Format error Memory card will appear on the message display. 1 Press Z while >Memory Card > is displayed. 2 >>Format appears - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 84
cannot be used for duplex printing, the Duplex disabled Press GO error message will be displayed and printing will stop. On • To print The display returns to Ready. Paper Mismatch (Detection settings for paper size/type errors when the paper source is fixed) Turn this setting to Off if you want - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 85
Auto Error Clear (Auto error clear setting) • Error Clear Timer (Setting the error clear time Out (Automatic form feed timeout setting) If the printer receives no data for a certain period, it will has in its buffer and feeds out the page. The default form feed timeout time is 30 seconds. 1 Press Z - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 86
a print job, the operation panel is operated, or one of the exterior covers is opened. The default time is 30 minutes. Note Color calibration is automatically executed before the printer reverts to normal operation mode. >>Sleep Timer 030 min. 1 Press Z while >Timer > is displayed. 2 Press U or - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 87
is shared over a network as a network printer and one person causes one of the above errors, after the set period of time elapses, the data sent from the next person is printed. The default setting is Off (Auto Error Clear disabled). The auto clear errors are: • Memory overflow Press GO • Print - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 88
until the error is recovered and printing resumes. 1 Press Z while >Timer > is displayed. 2 Press U or V repeatedly until >>Error Clear Timer appears Panel Reset function automatically restores the default settings if the panel is not used for a set time. The default setting is On. For setting the - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 89
>>Auto Sleep ? On Auto Sleep (Setting the sleep timer) The printer has a sleep timer that is used to conserve power when the printer is not printing, processing, or receiving data. 1 Press Z while >Timer > is displayed. 2 Press U or V repeatedly until >>Auto Sleep appears. 3 To turn off the sleep - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 90
Security The security functions can be set up to protect printer operation and the print data. The options available in Security are as follows: • ID (Administrator ID input) • Password (Administrator password input) • I/F Block (Interface (external device) block setting) • NetWare (NetWare setting - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 91
step (ID (Administrator ID input)), the message display shows Password (Administrator password input) and a blinking cursor (_). 2 Press U or slot setting) This locks and protects the USB memory slot (USB host). The default setting is Unblock. 1 Press Z while >I/F Block appears. > is displayed - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 92
setting) This locks and protects the network interface card (NIC). The default setting is Unblock. Note Option I/F is displayed only when the optional network interface is installed on the printer. 1 Press Z while >I/F Block appears. > is displayed. >>Option I/F 2 Press [OK]. A blinking question - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 93
Packet eXchange), but the system also supports TCP/IP. The feature of tools from the clients. Also, all drivers and protocol stacks are in the form default setting is On. Note Check with your network administrator when selecting network settings. 1 After entering the administrator ID and password - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 94
used to view websites and enables printing to be carried out via routers on printers in remote locations. It also supports the HTTP authentication mechanisms along with SSL server and client authentication as well as encryption. The default setting is Off. Note Check with your network administrator - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 95
use this protocol to authenticate servers and clients. The default setting is Off. Note Check with your network administrator when selecting network settings. >SSL Server 1 After entering the administrator ID and password, press U or V > repeatedly until >SSL Server > appears. >SSL Server - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 96
that uses SSL for communications between users and servers in network printing. To use IPP over SSL, both server and client must support the protocol. The default setting is Off. 1 Press Z while >SSL Server On > is displayed. >>IPP over SSL appears. 2 Press [OK]. A blinking question mark (?) appears - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 97
32-bit IP addresses and IPv6 uses 128-bit IP addresses. The default setting is Off. Note Check with your network administrator when selecting network settings. 1 After entering the administrator ID and password, press U or V repeatedly until >IPSec appears. 2 Press [OK]. A blinking question mark - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 98
Job accounting on this machine offers the following features: • Support for up to 100 departments • Department codes up to 8 digits long from 1 to 99999999 • as follows: • ID (Administrator ID input) • Password (Administrator Password input) • Job Accounting (Job Accounting selection/setting) - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 99
(Job Accounting selection/setting) This allows you to turn the Job Accounting function On and Off. The default setting is Off. 1 After entering the administrator ID and password, press U or V repeatedly until >Job Accounting appears. 2 Press [OK]. A blinking question mark (?) appears. 3 Select On or - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 100
>Select Account> ?00000000 Select Account (Department-specific settings) This specifies the functions used for managing individual account IDs. The options available in Select Account are as follows: • Counter (Account-specific counter management [color + monochrome total]) • Color Counter (Account - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 101
>>Restriction ? Off Restriction (Print restriction selection [color + monochrome total]) Sets restricted functionality for all printing on the currently selected account. You can use the restrictions to prohibit printing by individual departments or to limit the number of pages they can print. 1 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 102
>>Maximum Output 0000001 >>Color Max.out 0000001 >>Reset Counter? Maximum Output (Maximum print output setting [color + monochrome total]) Limits the number of pages for all printing on the currently selected account. 1 Set the account ID and then press U or V repeatedly until >>Maximum Output - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 103
account. IMPORTANT Because account IDs are managed as numeric strings, "1" and "001" are handled as different accounts. Also, once Job Accounting is enabled, no jobs are printed unless information is attached showing the accounts from which the jobs are being printed. 1 Press Z while Job Accounting - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 104
>Print Job Accounting List? Print Job Accounting List (Job Accounting list output) This enables you to print the total number of pages for all accounts as a Job Accounting list. 1 Press Z while Job Accounting > is displayed. 2 Press U or V repeatedly until > - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 105
setting is a function that identifies the user who can use the printer and can be used to manage users. The administrator is authenticated by the entered administrator ID and password and can then use the printer's security functions and Job Accounting functions. The options available in Admin - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 106
_ >Change ID 00000001 >Change ID 001 >Change ID _ OK? 002 Password (Administrator Password input) You can use this to set the administrator password. Note The default setting is "3000". 1 Once you have entered the correct ID in the previous step (ID (Administrator ID input)), the message display - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 107
Press U or V to increase or decrease, respectively, the value at the blinking cursor. Enter the password to be changed. Use Y and Z to move the cursor right and left. Enter a password consisting of between 0 and 16 numbers. 4 Press [OK]. A confirmation screen appears. (E.g.: Where the administrator - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 108
Calibration • Registration Normal (Color registration [standard]) • Registration Details (Color registration [detailed]) • Restart Printer • Service (for maintenance) IMPORTANT Service is primarily a menu used by service personnel for maintenance work. There is no need for customers to use this - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 109
>>Print Registra tion Chart ? Registration Normal (Color registration [standard]) When using the printer for the first time after set-up or after having moved it, or if printout of any color (magenta, cyan or yellow) is skewed, use - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 110
Sample Color Registration Correction Chart Color Registration Correction Chart MH-L IGECA13579 HFDB02468 MV I G E C A 1 3 5 7 9 H F D B 0 2 4 6 8 MH-R IGECA13579 HFDB02468 CH-L IGECA13579 HFDB02468 CV I G E C A 1 3 5 7 9 H F D B 0 2 4 6 8 CH-R IGECA13579 HFDB02468 YH-L IGECA13579 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 111
>>Adjust Magenta L=0 V=0 R=0 Adjust Magenta Corrects the registration for magenta (red). 1 Press Z while Adjust/Maintenance > is displayed. 2 Press U or V repeatedly until >Registration Normal > appears. 3 Press Z. 4 Press U or V repeatedly until >>Adjust Magenta appears. 5 Press [OK]. 0 will be - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 112
line is not 0, redo the settings again from step 4 above. IMPORTANT If the problem of skewed-color printout still persists even after correcting the color registration, call for service. Registration Details (Color registration [detailed]) This allows you to make fine horizontal and vertical - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 113
6 Press [OK]. Processing appears and a color registration correction chart is printed out. There are horizontal (H) and vertical (V) registration charts for each color (magenta, cyan and yellow) included on the color registration correction chart. 7 When printing ends, the display returns to Ready. - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 114
>>M 12345 3 MH=00000 MV=0 M 12345 3 (Adjust magenta) Makes detailed corrections to the registration for magenta (red). 1 Press Z while Adjust/Maintenance > is displayed. 2 Press U or V repeatedly until >Registration Details > appears. 3 Press Z. 4 Press U or V repeatedly until >>M 12345 3 appears. - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 115
If the problem of skewed-color printout still persists even after correcting the color registration, call for service. Restart Printer The procedure described below resets the printer's temporary conditions, such as the current page orientation, font, etc., set by commands to their default values - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 116
charger cleaning mode setting) • Drum (Drum/Refresh mode setting) IMPORTANT Service is primarily a menu used by service personnel service status page) The service status page contains printer settings information that is more detailed than the standard status page and is therefore mostly for service - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 117
Print Test Page The test page is printed to check the effectiveness of printer adjustments. This is primarily used for maintenance by service personnel, but it contains information that may also be useful to you. 1 Press Z while >Service > is displayed. 2 Press U or V repeatedly until >>Print Test - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 118
mode for the LSU/Main charger. When the printing quality declines, cleaning the LSU/Main charger can restore the printing quality. This is primarily used for maintenance by service personnel. 1 Press Z while >Service > is displayed. 2 Press U or V repeatedly until >>LSU/Charger appears. 3 Press [OK - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 119
3 Options This chapter contains explanations on the following topics: General Information 3-2 Expansion Memory Modules 3-3 General Description of Options 3-5 For availability of the options, consult your service technician. Options 3-1 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 120
General Information This printer has the following options available to satisfy your printing requirements. For instructions on installing individual options, refer to the documentation included with the option. Some options are explained in the following sections. Expansion Memory (DIMM 128/256/ - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 121
's main controller board has a memory slot into which you can plug in optional memory modules (dual in line memory modules). You can increase the printer's memory up to 1280 MB by plugging in the optional memory modules. Note A 256 MB memory module is already installed at the factory. To expand - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 122
Installing the Memory Modules IMPORTANT Remove any USB memory that is attached to the printer's USB memory slot. 1 Power off the printer and unplug the printer power cord. 2 Unscrew two screws at the back of the main controller board. Main Controller Board 3 Pull out the main controller board - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 123
, the contents of the memory card can be read from the operation panel or automatically when you power on or reset the printer. To manually read data in the memory card, refer to Memory Card (Using the memory card) on page 2-58. Formatting the Memory Card To use an unused - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 124
-510 to the printer and installing it manual supplied with the base. IMPORTANT Be careful to not trip on the feet of the base. Hard Disk Insert the hard disk into the option interface slot. The hard disk is used to store print data. This provides benefits such as the ability to print multiple copies - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 125
in USB memory can be printed by plugging the USB memory into the printer and then specifying the desired file names from the operation panel. The text in the message list. Also, when the file is printed an error message appears and printing fails. For information on printing PDF files stored in - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 126
3-8 Options - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 127
4 Computer Interface This chapter contains explanations on the following topics: Interface 4-2 USB Interface 4-2 Network Interface 4-3 Computer Interface 4-1 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 128
lists pin assignments, signal functions, timings, connector specifications, and voltage levels. • USB Interface • Network Interface USB Interface This printer supports the Hi-Speed USB. USB (Universal Serial Bus) interface specifications and interface signals are as follows. Specifications Basic - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 129
be password-protected. Support for a Range of Protocols The SMTP, POP3, SSL, SNMP, IPv6 and NetBIOS over TCP/IP protocols are supported for easier printer management and more robust security. Support for IEEE 802.1x The interface supports EAP-TLS and PEAP authentication. Supports IPv6 Supports IPv6 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 130
Operation Environment 10 to 35 °C (50 to 95 °F), 20-80 % RH (condensation-free) EMI Countermeasures VCCI Class B, FCC Class B (U.S.), CE (Europe) IMPORTANT When IPv6 functions are used, the devices used on the network (routers, PCs, etc) must support IPv6. 4-4 Computer Interface - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 131
computer on the same AppleTalk network. Custom Box The Custom Box function stores print data for each individual user on the printer and allows the user to print single or multiple copies of the stored data later using the printer's operation panel. Default Gateway This indicates the device, such as - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 132
should be a decimal between 0 and 255. Job Box The Job Box function stores print data on the printer and allows users to print single or multiple copies of the stored data later using the printer's operation panel. KPDL KPDL is Kyocera's implementation of the PostScript page description language - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 133
period of time. In this mode, power is reduced to the minimum. The default setting can be changed. Status page This lists machine conditions, such as the An interface standard for low to middle speed serial interfaces. This printer supports Hi-Speed USB. The maximum transfer rate is 480 Mbps and - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 134
Glossary-4 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 135
2-74, 2-81 Change 2-82 Administrator Password 2-67, 2-75, 2-82 Change 2-83 75 Job Box 2-23 Configuration 2-28 Private Print Job 2-27 Proof-and-Hold 2-26 Quick Copy 2-24 Job Retention 2-23 K Keys Arrow keys 2-6 Basic operation 2-6 Cancel 2-6 GO 2-6 MENU 2-6 OK 2-7 KPDL Errors - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 136
Page Set Number of copies 2-45 Print orientation 2- Custom 2-37 Print Custom Box List 2-22 Fonts Error clear time 2-64 Panel reset 2-64 Sleep 2-62 U Unit of measurement 2-34 USB Interface 2-67, 4-2 USB Memory 2-17 USB Memory Slot 2-68 R RAM Disk 2-56 Restart Printer 2-91 S Service - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 137
We recommend the use of our own brand supplies. We will not be liable for any damage caused by the use of third party supplies in this machine. A1 - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 138
- Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 139
2009 is a trademark of Kyocera Corporation - Kyocera FS-C5350DN | FS-C5350DN Operation Guide (Advanced) - Page 140
First edition 2009.5
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
 |
 |
Advanced Operation Guide
FS-C5350DN