Kyocera KM-2030 Printing System (K) Instruction Handbook (Setup Edition) - Page 75

List of settings, Item No., Display message, Available settings, Remarks

Get Kyocera KM-2030 PDF manuals and user guides View all Kyocera KM-2030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

2. Printer Settings (20 ppm copier) 2-3 List of settings Item No. Item Display message Available settings Remarks 1 Printer Status Page print out Prints out a list of such items as printer default settings and memory volume, etc. Print Status Page No, Print 2 Interface selection When the optional Network Card is installed, the available interfaces are displayed. The arrow (>) will indicate the currently selected interface. The printer will automatically switch to the appropriate interface for printing. Interface Parallel, Option "Option" is displayed only when the Network Card is installed. 3 Parallel TX/RX mode Sets the transmission and reception mode when the printer is connected to your computer with a parallel interface. Parallel Auto, Normal, High Speed, Nibble (high) 4 NetWare ON/OFF NetWare On, Off Displayed only when the Network Card is installed. 5 NetWare frame type Sets the NetWare frame type. NetWare Frame Auto, 802.3, Ethernet II, 802.2, 802.3 SNAP Displayed only when the NetWare setting is turned "On". 6 TCP/IP ON/OFF TCP/IP On, Off Displayed only when the Network Card is installed. 7 DHCP ON/OFF DHCP On, Off Displayed only when the Network Card is installed. 8 IP address IP Address Enter the address. Displayed only when the Network Card is installed. 9 Subnet Mask Subnet Mask Enter the address. Displayed only when the Network Card is installed. 10 Gateway address Gateway Enter the address. Displayed only when the Network Card is installed. 11 EtherTalk ON/OFF EtherTalk On, Off Displayed only when the Network Card is installed. 12 Network Card Status Page print out ON/ OFF Opt. StatusPage On, Off Sets whether a Status Page regarding conditions in the Network Card will be printed out as well when the standard Status Page for the printer (item No.: 1) or that for use by your service representative (item No.: 60) are printed out. A more detailed Status Page is printed out together with the "Service Rep Status Page print out" setting (item No.: 1). Displayed only when the Network Card is installed. 13 Emulation protocol Sets the emulation protocol that will be used. Emulation Line Printer, IBM Proprinter, DIABLO 630, EPSON LQ-850, PCL 6, KPDL, KPDL (AUTO) Allows you to set a different emulation for the parallel interface and the Network Card (option). Select the desired interface under the "Interface selection" setting (item No.: 2). 2-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
2-7
2. Printer Settings (20 ppm copier)
2-3
List of settings
Item No.
1
2
3
4
5
6
7
8
9
10
11
12
13
Item
Printer Status Page print out
Prints out a list of such items as printer
default settings and memory volume, etc.
Interface selection
When the optional Network Card is installed,
the available interfaces are displayed. The
arrow (>) will indicate the currently selected
interface. The printer will automatically
switch to the appropriate interface for
printing.
Parallel TX/RX mode
Sets the transmission and reception mode
when the printer is connected to your
computer with a parallel interface.
NetWare ON/OFF
NetWare frame type
Sets the NetWare frame type.
TCP/IP ON/OFF
DHCP ON/OFF
IP address
Subnet Mask
Gateway address
EtherTalk ON/OFF
Network Card Status Page print out ON/
OFF
Sets whether a Status Page regarding
conditions in the Network Card will be
printed out as well when the standard Status
Page for the printer (item No.: 1) or that for
use by your service representative (item No.:
60) are printed out. A more detailed Status
Page is printed out together with the
“Service Rep Status Page print out” setting
(item No.: 1).
Emulation protocol
Sets the emulation protocol that will be used.
Display message
Print Status Page
Interface
Parallel
NetWare
NetWare Frame
TCP/IP
DHCP
IP Address
Subnet Mask
Gateway
EtherTalk
Opt. StatusPage
Emulation
Available settings
No, Print
Parallel, Option
Auto, Normal,
High Speed,
Nibble (high)
On, Off
Auto, 802.3,
Ethernet II, 802.2,
802.3 SNAP
On, Off
On, Off
Enter the address.
Enter the address.
Enter the address.
On, Off
On, Off
Line Printer,
IBM Proprinter,
DIABLO 630,
EPSON LQ-850,
PCL 6, KPDL,
KPDL (AUTO)
Remarks
“Option” is displayed only when the
Network Card is installed.
Displayed only when the Network
Card is installed.
Displayed only when the NetWare
setting is turned “On”.
Displayed only when the Network
Card is installed.
Displayed only when the Network
Card is installed.
Displayed only when the Network
Card is installed.
Displayed only when the Network
Card is installed.
Displayed only when the Network
Card is installed.
Displayed only when the Network
Card is installed.
Displayed only when the Network
Card is installed.
Allows you to set a different
emulation for the parallel interface
and the Network Card (option).
Select the desired interface under
the “Interface selection” setting
(item No.: 2).