Lenovo NetVista Hardware Maintenance Manual (HMM) for NetVista 6832 and 6833 s - Page 141

Change the Machine Type and Serial Number in, System Board Installation

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 141 highlights

NOTE: System Board Installation • Before reinstallation, position the housing on its side. When installing a new system board, push the board to the rear and align it with the front locating pin. Visually verify that the board is aligned properly, then press the board down. • Be sure to reinstall the processor, DIMMs, I/O port bracket onto the new system board if applicable. • After installing the system board, secure with original screws. • Change all jumper settings to match those of the original board. • Reinstall other components into the machine i.e. drives, power supply, cables, etc. • Upgrade the BIOS version on the new system board using the BIOS upgrade utility. • Change the Machine Type and Serial Number in the BIOS to match the original planar BIOS settings. • Reboot the system and run the Configuration/ Setup Utility. General Information 109

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
General Information
109
NOTE:
System Board Installation
•
Before reinstallation, position the housing on its
side. When installing a new system board, push
the board to the rear and align it with the front
locating pin. Visually verify that the board is
aligned properly, then press the board down.
•
Be sure to reinstall the processor, DIMMs, I/O port
bracket onto the new system board if applicable.
•
After installing the system board, secure with
original screws.
•
Change all jumper settings to match those of the
original board.
•
Reinstall other components into the machine i.e.
drives, power supply, cables, etc.
•
Upgrade the BIOS version on the new system
board using the BIOS upgrade utility.
•
Change the Machine Type and Serial Number in
the BIOS to match the original planar BIOS
settings.
•
Reboot the system and run the Configuration/
Setup Utility.