Lenovo NetVista Hardware Maintenance Manual (HMM) for NetVista 6832 and 6833 s - Page 95

Power Supply, When The On/off Switch Is Pressed? Yes

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Power Supply 001 - START • Power off (unplug) the system unit. Check the power cord for continuity. Replace if necessary. • Check for the correct line voltage from the power outlet, and verify that the voltage selector switch (if present) is set to the correct voltage. • Power on the system unit. 002 - DOES THE POWER SUPPLY FAN RUN? (YES, GO TO STEP 003. NO, GO TO STEP 004.) 003 - DOES THE SYSTEM FAIL TO SHUT OFF WHEN THE ON/OFF SWITCH IS PRESSED? (YES, READ AHEAD. NO, GO TO STEP 005.) • You might have a damaged on/off switch cable assembly. • Disconnect the on/off switch cable assembly connector from the power supply connector and take an ohm reading. • Go to step 007. 004 • Disconnect the power cord from the back of the system unit. • Disconnect all power and switch cable connectors from the system board and the power supply. • Disconnect the power connectors to all drives. • Connect any one of the power connector to system board or drive as power load for driving up power supply. • Reconnect the power cord and turn on the power supply. Check Procedures 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
Check Procedures
63
Power Supply
001 -
START
•
Power off (unplug) the system unit. Check the
power cord for continuity. Replace if necessary.
•
Check for the correct line voltage from the power
outlet, and verify that the voltage selector switch (if
present) is set to the correct voltage.
•
Power on the system unit.
002 - DOES THE POWER SUPPLY FAN RUN?
(YES, GO TO STEP 003. NO, GO TO STEP 004.)
003 - DOES THE SYSTEM FAIL TO SHUT OFF
WHEN THE ON/OFF SWITCH IS PRESSED? (YES,
READ AHEAD. NO, GO TO STEP 005.)
•
You might have a damaged on/off switch cable
assembly.
•
Disconnect the on/off switch cable assembly
connector from the power supply connector and
take an ohm reading.
•
Go to step 007.
004 -
•
Disconnect the power cord from the back of the
system unit.
•
Disconnect all power and switch cable connectors
from the system board and the power supply.
•
Disconnect the power connectors to all drives.
•
Connect any one of the power connector to system
board or drive as power load for driving up power
supply.
•
Reconnect the power cord and turn on the power
supply.