Pioneer SC-05 Owner's Manual - Page 105

Controlling the rest of your system 14 Multi Operation and System Off The Multi Operation feature allows you to program a series of up to 5 commands for the components in your system. For example, you could turn on your TV, turn on your DVD player and start playing the loaded DVD using only two buttons on the remote control. Similar to multi operations, System Off allows you to use one button to stop and switch off a series of components in your system at the same time.1 Programming a multi-operation or a shutdown sequence Set the remote control operation mode selector switch to RCV when you want to program this receiver's operations, to SOURCE when you want to program operations of other components. RECEIVER MAIN ZONE2 DVD BD SOURCE 3 MULTI OPERATION DTVVR1 DVR12 VIDEO1 VIDEO2 VIDEO3 DTVVR2 HOME MEDIA GALLERY CD CD-R PHONO HDMI TUNER XM SIRIUS INPUT SELECT TV CONTROL INPUT MUTE AUDIO PARAMETER EXIT TUNE MUTE VIDEO PARAMETER TOOLS TOP MENU BAND ST ENTER MENU T.EDIT ST CATEGORY HOME MENU iPod CTRL TUNE STATUS PHASE CTRL RETURN CH LEVEL THX MPX MEMORY 1 While pressing MULTI OPERATION, press HOME MENU. The remote LCD display shows SETUP. 2 Use / to select MULTI OP or SYS OFF from the menu and press ENTER. If you selected Multi Operation (MULTI OP), the LCD on the remote prompts you for an input source button. If you selected System Off (SYS OFF), go to step 4. 3 Press the input source button for the component that will start the multi-operation, then press ENTER. For example, if you want to start the sequence by switching on your DVD player, press DVD. 4 Use / to select CODE EDT, then press ENTER. To erase any previously stored multi-operations (or shutdown sequences) select CODE ERS above. 5 Use / to select a command in the sequence, then press ENTER. If this is the first command in the sequence, select 1ST CODE. Otherwise, simply choose the next command in the sequence. PRES KEY flashes after you press ENTER. 6 If necessary, press the input source button for the component whose command you want to input. This is only necessary if the command is for a new component (input source). 7 Select the button for the command you want to input. The following remote control commands can be selected: RECEIVER MAIN ZONE2 DVD BD SOURCE 3 MULTI OPERATION DVR1 DVR2 VIDEO1 VIDEO2 VIDEO3 TV HOME MEDIA GALLERY CD CD-R PHONO HDMI TUNER XM SIRIUS INPUT SELECT AUDIO PARAMETER EXIT TUNE VIDEO PARAMETER TOOLS TOP MENU BAND ST ENTER MENU T.EDIT ST CATEGORY HOME MENU iPod CTRL TUNE STATUS PHASE CTRL RETURN CH LEVEL THX MPX MEMORY AUTO/ DIRECT PGM STEREO/ A.L.C. STANDARD ADV SURR BD MENU SIGNAL SEL SLEEP DIMMER AUDIO SOURCE TV RCV SR+ SBch MCACC DISP A.ATT GENRE HDMI OUT CH VOL VOL D.ACCESS CLASS CH ENTER CLR TV CONTROL INPUT MUTE MUTE AUDIO VIDEO • You don't need to program the receiver to switch on or off. This is done automatically. With Pioneer components, you don't need to: • program the power to switch off in a shutdown sequence (except DVD recorders); • program the power to switch on if it's the source component selected in step 3; • program a Pioneer TV or monitor to switch on if the input function (selected in step 2) has video input terminals; These take priority in multi operations (not shutdown). 8 Repeat steps 5 to 7 to program a sequence of up to five commands. 9 When you're finished, use / to select EXIT from the menu and press ENTER. You will return to the remote control Setup menu. Select * EXIT * again to exit. Note 1 • Before Multi Operation and System Off will work correctly, you must setup the remote to work with your TV and other components (see Setting the remote to control other components on page 102 for more on this). • Some units may take some time to power up, in which case multiple operations may not be possible. • Power on and off commands only work with components that have a standby mode. 105 En