Ricoh AP610N Setup Guide - Page 42

side groove of the duplex unit

Get Ricoh AP610N - Aficio B/W Laser Printer PDF manuals and user guides
UPC - 026649023385
View all Ricoh AP610N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Installing Options L Fasten the controller board to the printer with the two screws. 3 ZKGX270E M Align the power cable to the left side groove of the duplex unit, and then slide the duplex unit in until it is connected to the printer. ZKGX243E If the duplex unit is not attached, this step is not necessary. Note ❒ Be sure to return the provided screwdriver to its original position on the inside of the front cover. ❒ After finishing the installation, you can check the memory unit is properly installed: Print the configuration page from the "List/Test Print" menu. If it is installed properly, you will see the memory capacity for "Total Memory". ❒ To expand memory, remove the default SDRAM module, and then install the SDRAM module (256 MB). "Total Memory" will be the size of SDRAM module memory unit you installed. ❒ If the memory unit is not properly installed, repeat the procedure from the start. If you cannot install it properly even after reinstallation, contact your sales or service representative. Reference For printing the configuration page, see p.28 "Test Printing". 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Installing Options
38
3
L
Fasten the controller board to the
printer with the two screws.
M
Align the power cable to the left
side groove of the duplex unit,
and then slide the duplex unit in
until it is connected to the printer.
If the duplex unit is not attached,
this step is not necessary.
Note
❒
Be sure to return the provided
screwdriver to its original posi-
tion on the inside of the front
cover.
❒
After finishing the installation,
you can check the memory unit
is properly installed: Print the
configuration page from the
“List/Test Print” menu. If it is
installed properly, you will see
the memory capacity for “Total
Memory”.
❒
To expand memory, remove the
default SDRAM module, and
then install the SDRAM module
(256 MB). “Total Memory” will
be the size of SDRAM module
memory unit you installed.
❒
If the memory unit is not prop-
erly installed, repeat the proce-
dure from the start. If you
cannot install it properly even
after reinstallation, contact your
sales or service representative.
Reference
For printing the configuration
page, see p.28 “Test Printing”.
ZKGX270E
ZKGX243E