Ricoh AP610N Setup Guide - Page 47

Attaching 802.11b Interface Unit Type F

Get Ricoh AP610N - Aficio B/W Laser Printer PDF manuals and user guides
UPC - 026649023385
View all Ricoh AP610N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Attaching 802.11b Interface Unit Type F Attaching 802.11b Interface Unit Type F R CAUTION: • Do not touch the inside of the controller board compartment. Doing so may cause a machine malfunction or a burn. • Antenna Cap Important ZKDP900J ❒ Before touching the 802.11b interface unit, touch something metal to B Turn off the power of the printer, 3 discharge any static electricity. and then unplug the printer's Static electricity can damage the 802.11b interface unit. power cable and the interface cable. C ❒ Do not subject the 802.11b interface If the duplex unit is attached, unit to physical shocks. push down the lever on right side A Check the package contains the following: ( ) and pull out the duplex unit until it stops ( ). ❖ 802.11b Interface Unit Type F • Interface Unit • Card ZKGX320E If the duplex unit is not attached, go to the following steps. ZKDP410J ZKDX230J 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Attaching 802.11b Interface Unit Type F
43
3
Attaching 802.11b Interface Unit Type F
R
CAUTION:
Important
❒
Before touching the 802.11b inter-
face unit, touch something metal to
discharge any static electricity.
Static electricity can damage the
802.11b interface unit.
❒
Do not subject the 802.11b interface
unit to physical shocks.
A
Check the package contains the
following:
❖
802.11b Interface Unit Type F
•
Interface Unit
• Card
•
Antenna Cap
B
Turn off the power of the printer,
and then unplug the printer's
power cable and the interface ca-
ble.
C
If the duplex unit is attached,
push down the lever on right side
(
) and pull out the duplex unit
until it stops (
).
If the duplex unit is not attached,
go to the following steps.
•
Do not touch the inside of the
controller board compartment.
Doing so may cause a machine
malfunction or a burn.
ZKDP410J
ZKDX230J
ZKDP900J
ZKGX320E