Ricoh AP610N Setup Guide - Page 54

facing the screws.

Get Ricoh AP610N - Aficio B/W Laser Printer PDF manuals and user guides
UPC - 026649023385
View all Ricoh AP610N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Installing Options N Fasten the controller board to the printer with the two screws. Q Align the power cable to the left side groove of the duplex unit, and then slide the duplex unit in until it is connected to the printer. 3 ZKGX602E O Press the antenna to extend it. ZKGX603E P Attach the antenna cap to the card with the side that has both corners of the antenna cap cut out facing the screws. ZKGX604E ZKGX240E If the duplex unit is not attached, this step is not necessary. Note ❒ After finishing installation, you can check the Bluetooth interface unit is properly installed: Print the configuration page from the "List/Test Print" menu. If it is installed properly, you will see "Bluetooth" for "Controller Option". ❒ If the Bluetooth interface unit is not installed properly, repeat the procedure from the start. If you cannot install it properly even after reinstallation, contact your sales or service representative. Reference For printing the configuration page, see p.28 "Test Printing". 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Installing Options
50
3
N
Fasten the controller board to the
printer with the two screws.
O
Press the antenna to extend it.
P
Attach the antenna cap to the card
with the side that has both cor-
ners of the antenna cap cut out
facing the screws.
Q
Align the power cable to the left
side groove of the duplex unit,
and then slide the duplex unit in
until it is connected to the printer.
If the duplex unit is not attached,
this step is not necessary.
Note
❒
After finishing installation, you
can check the Bluetooth inter-
face unit is properly installed:
Print the configuration page
from the “List/Test Print”
menu. If it is installed properly,
you will see “Bluetooth” for
“Controller Option”.
❒
If the Bluetooth interface unit is
not installed properly, repeat
the procedure from the start. If
you cannot install it properly
even after reinstallation, contact
your sales or service representa-
tive.
Reference
For printing the configuration
page, see p.28 “Test Printing”.
ZKGX602E
ZKGX603E
ZKGX604E
ZKGX240E