Ricoh AP610N Setup Guide - Page 48

Place the controller board on a flat

Get Ricoh AP610N - Aficio B/W Laser Printer PDF manuals and user guides
UPC - 026649023385
View all Ricoh AP610N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Installing Options D H Remove the two screws holding Remove the two screws and the the controller board in place. cover of the 802.11b interface unit Note mounting bracket. ❒ Use a coin or similar object if the Note screws do not turn easily. ❒ These screws are used again in ❒ These screws are used again in fastening the controller board. fastening the 802.11b interface unit to the controller board. ❒ The removed cover is not used when installing the 802.11b in- 3 terface unit. ZKGX280E E Pull out the handle of the control- ler board. ZKGX410E I Attach the 802.11b interface unit. Insert the end of the 802.11b interface unit into the opening ( ), and then push down until it clicks ( ). ZKGX370E F Pull the handle, and then slide the controller board out. ZKGX420E ZKGX260E G Place the controller board on a flat 44 surface. ZKGX431E

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Installing Options
44
3
D
Remove the two screws holding
the controller board in place.
Note
❒
Use a coin or similar object if the
screws do not turn easily.
❒
These screws are used again in
fastening the controller board.
E
Pull out the handle of the control-
ler board.
F
Pull the handle, and then slide
the controller board out.
G
Place the controller board on a flat
surface.
H
Remove the two screws and the
cover of the 802.11b interface unit
mounting bracket.
Note
❒
These screws are used again in
fastening the 802.11b interface
unit to the controller board.
❒
The removed cover is not used
when installing the 802.11b in-
terface unit.
I
Attach the 802.11b interface unit.
Insert the end of the 802.11b inter-
face unit into the opening (
), and
then push down until it clicks (
).
ZKGX280E
ZKGX370E
ZKGX260E
ZKGX410E
ZKGX420E
ZKGX431E