Ricoh AP610N Setup Guide - Page 46

and then slide the duplex unit

Get Ricoh AP610N - Aficio B/W Laser Printer PDF manuals and user guides
UPC - 026649023385
View all Ricoh AP610N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Installing Options M Fasten the controller board to the printer with the two screws. 3 ZKGX272E N Align the power cable to the left side groove of the duplex unit, and then slide the duplex unit in until it is connected to the printer. Note ❒ After finishing installation, you can check the 1394 interface unit is properly installed: Print the configuration page from the "List/Test Print" menu. If it is installed properly, you will see "IEEE1394" for "Controller Option". ❒ You need to make settings with the control panel before using the 1394 interface unit. For more information, see p.68 "IEEE 1394 Configuration". ❒ If the 1394 interface unit is not installed properly, repeat the procedure from the start. If you cannot install it properly even after reinstallation, contact your sales or service representative. Reference For printing the configuration page, see p.28 "Test Printing". ZKGX242E If the duplex unit is not attached, this step is not necessary. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Installing Options
42
3
M
Fasten the controller board to the
printer with the two screws.
N
Align the power cable to the left
side groove of the duplex unit,
and then slide the duplex unit in
until it is connected to the printer.
If the duplex unit is not attached,
this step is not necessary.
Note
❒
After finishing installation, you
can check the 1394 interface unit
is properly installed: Print the
configuration page from the
“List/Test Print” menu. If it is
installed properly, you will see
“IEEE1394” for “Controller Op-
tion”.
❒
You need to make settings with
the control panel before using
the 1394 interface unit. For more
information, see p.68 “IEEE
1394 Configuration”.
❒
If the 1394 interface unit is not
installed properly, repeat the
procedure from the start. If you
cannot install it properly even
after reinstallation, contact your
sales or service representative.
Reference
For printing the configuration
page, see p.28 “Test Printing”.
ZKGX272E
ZKGX242E