Samsung WMN5090 Installation Instructions - Page 7

Installation

Get Samsung WMN5090 PDF manuals and user guides View all Samsung WMN5090 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

3 Installation (LCD 4652", PDP 42-50") For information on installing a wall mount for a 40" LCD, See "4. Installation (40" LCD)" 3-1 Fix your wall mount to the wall, as shown in the figure below. 0® O ® 0 TT T T T Q • • Q ® Fixing Anchors and Screws (on to a concrete wall) Create a hole in the wall using a 9X50 drill. Clean the hole. Insert one of the provided anchors una into the hole. Q Align the angle adjustment device with the hole and fasten a screw Ca). 11 When drilling a hole into the wall, make sure to use a drill 0 bit and drill with the specified diameter. Failing to do so may cause personal injury. Level the wall mount and fix it using the anchors and screws ®, as shown in the figure below. First fasten screw 0 Then hang the wall mount and fasten the remaining screws. (However, angle adjustment devices must be fixed at locations 0, 0, ©, 0, and C).) idt)n 1. Check the strength of the wall before the installation. If it is not strong enough for the installation, make sure to reinforce it and then install the product onto it. 2. The screws and anchors provided are for both wood and concrete surfaces. 3. Check the wall and use the appropriate specialized screws for marble and steel walls. 4. For plasterboard walls, locate wooden sections using a stud finder and fix your wall mount to these. Use the appropriate spe- cialized screws for plasterboard. 5. After hanging your TV onto the wall mount, make sure to check that it hangs correctly by inspecting it from both left and right. 6. During the installation and the angle adjustment, avoid getting your fingers caught. 7. If the wall mount support is not fixed to the wall firmly, it may cause the TV to fall and cause personal injury. Ensure that it is fixed to the wall firmly. 8. Do not pull the wall mount more than 45° to the left and forwards when fastening the screws. 5 The wall mount ships set up for a 50" PDP. You need to check the size of your TV and if it is not a 50"PDP, you need to change the settings of your wall mount. For more information on how to configure the settings, see "5. Adjusting the Wall Mount to the TV Size." 3-2 For a TV equipped with a stand, remove the stand and remove the four (4) screws on the back of the TV, as shown in the figure below.(For information on how to remove the stand from the TV, refer to your TV manual. Removing the stand differs for each TV.) 8 °E- 1 , MaNII0 ,, . , 0 0

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
3
Installation
(LCD
4652",
PDP
42-50")
For
information
on
installing
a
wall
mount
for
a
40"
LCD,
See
"4.
Installation
(40"
LCD)"
3
-1
Fix
your
wall
mount
to
the
wall,
as
shown
in
the
figure
below.
3-2
0
®
O
®
0
TT
T
T
T
Q
•
•
11
Q
Q
0
Fixing
Anchors
and
®
Screws
(on
to
a
concrete
wall)
una
Create
a
hole
in
the
wall
using
a
9X50
drill.
Clean
the
hole.
Insert
one
of
the
provided
anchors
into
the
hole.
Align
the
angle
adjustment
device
with
the
hole
and
fasten
a
screw
Ca).
When
drilling
a
hole
into
the
wall,
make
sure
to
use
a
drill
bit
and
drill
with
the
specified
diameter.
Failing
to
do
so
may
cause
personal
injury.
Level
the
wall
mount
and
fix
it
using
the
anchors
and
screws
®,
as
shown
in
the
figure
below.
First
fasten
screw
0
Then
hang
the
wall
mount
and
fasten
the
remaining
screws.
(However,
angle
adjustment
devices
must
be
fixed
at
locations
0, 0,
©,
0,
and
C).)
idt)n
1.
Check
the
strength
of
the
wall
before
the
installation.
If
it
is
not
strong
enough
for
the
installation,
make
sure
to
reinforce
it
and
then
install
the
product
onto
it.
2.
The
screws
and
anchors
provided
are
for
both
wood
and
concrete
surfaces.
3.
Check
the
wall
and
use
the
appropriate
specialized
screws
for
marble
and
steel
walls.
4.
For
plasterboard
walls,
locate
wooden
sections
using
a
stud
finder
and
fix
your
wall
mount
to
these.
Use
the
appropriate
spe-
cialized
screws
for
plasterboard.
5.
After
hanging
your
TV
onto
the
wall
mount,
make
sure
to
check
that
it
hangs
correctly
by
inspecting
it
from
both
left
and
right.
6.
During
the
installation
and
the
angle
adjustment,
avoid
getting
your
fingers
caught.
7.
If
the
wall
mount
support
is
not
fixed
to
the
wall
firmly,
it
may
cause
the
TV
to
fall
and
cause
personal
injury.
Ensure
that
it
is
fixed
to
the
wall
firmly.
8.
Do
not
pull
the
wall
mount
more
than
45°
to
the
left
and
forwards
when
fastening
the
screws.
5
The
wall
mount
ships
set
up
for
a
50"
PDP.
You
need
to
check
the
size
of
your
TV
and
if
it
is
not
a
50"PDP,
you
need
to
change
the
settings
of
your
wall
mount.
For
more
information
on
how
to
configure
the
settings,
see
"5.
Adjusting
the
Wall
Mount
to
the
TV
Size."
For
a
TV
equipped
with
a
stand,
remove
the
stand
and
remove
the
four
(4)
screws
on
the
back
of
the
TV,
as
shown
in
the
figure
below.(For
information
on
how
to
remove
the
stand
from
the
TV,
refer
to
your
TV
manual.
Removing
the
stand
differs
for
each
TV.)
8
°E
-
1
,
MaNII0
.
,
,
0
0
,