Sharp AR-337 AR-287 , AR-337 , AR-407 Operation Manual - Page 101

Self-diagnostic function - error codes

Get Sharp AR-337 PDF manuals and user guides View all Sharp AR-337 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

TROUBLESHOOTING 5 CHAPTER Problem Solution Dust, dirt, smudges appear q Document glass, RADF transport Clean regularly. See page 6-6. on copies. belt dirty? Touch panel is too dark or q Is LCD contrast properly too light. adjusted? Adjust the LCD contrast. See page 6-7. "CHECK THE SUB MACHINE." message appears and the tandem copying does not start. q Some message appears on the touch panel of the sub copier? Follow the message on the sub copier to solve the problem. "THE SYSTEM IS NOT CONFIGURED TO PERFORM TANDEM JOB. CODE: XX" message appears and the tandem copying can not be performed. q The same options are equipped for the main and sub copiers? q The settings in the following key operator programs are different on the main and sub copiers: * Disabling of Duplex Copying (error code No. 51) * Disabling of Stapler (error code No. 52) * Disabling of Bypass-Tray When Offset Tray Selected (error code No. 53: only with AR-FN2) Tandem copying is not performed unless the same options are equipped for both main and sub copiers. Tandem copying is not performed unless the settings in these key operator programs are the same on both main and sub copiers. If a problem persists after checking the above, please consult your authorized Sharp Service Center. Self-diagnostic function An automatic self-diagnostic function is built into this copier. Should the copier malfunction, the self-diagnostic function will locate the problem and stop the copier to prevent damage. An alphanumeric code will appear in the message display. Example Should the copier stop completely, and the message "CALL FOR SERVICE. CODE: " appear in the message display, contact your authorized Sharp Service Center. 5 KEY OPERATOR See page 29 of the KEY OERATOR'S GUIDE. 5-13 COPIER TROUBLE? Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
5-13
CHAPTER
5
COPIER TROUBLE?
Troubleshooting
TROUBLESHOOTING
Problem
Solution
Dust, dirt, smudges appear
on copies.
Touch panel is too dark or
too light.
“
CHECK THE SUB
MACHINE.
”
message
appears and the tandem
copying does not start.
“
THE SYSTEM IS NOT
CONFIGURED TO PERFORM
TANDEM JOB. CODE: XX
”
message appears and the
tandem copying can not be
performed.
●
Document glass, RADF transport
belt dirty?
●
Is LCD contrast
properly
adjusted?
●
Some message appears on the
touch panel of the sub copier?
●
The same options are equipped
for the main and sub copiers?
●
The settings in the following key
operator programs are different
on the main and sub copiers:
*
Disabling of Duplex Copying
(error code No. 51)
*
Disabling of Stapler (error
code No. 52)
*
Disabling of Bypass-Tray
When Offset Tray Selected
(error code No. 53: only with
AR-FN2)
Clean regularly. See page 6-6.
Adjust the LCD contrast.
See page 6-7.
Follow the message on the sub copier
to solve the problem.
Tandem copying is not performed unless
the same options are equipped for both
main and sub copiers.
Tandem copying is not performed unless
the settings in these key operator
programs are the same on both main
and sub copiers.
If a problem persists after checking the above, please consult your
authorized Sharp Service Center.
Self-diagnostic function
An automatic self-diagnostic function is built into this copier. Should the
copier malfunction, the self-diagnostic function will locate the problem
and stop the copier to prevent damage. An alphanumeric code will
appear in the message display.
Example
Should the copier stop completely, and the message “
CALL FOR
SERVICE. CODE:
” appear in the message display, contact your
authorized Sharp Service Center.
KEY OPERATOR
See page 29 of the KEY OERATOR’S GUIDE.