TP-Link Archer D5 Archer D5 V1 User Guide - Page 38

Set IPv6 DNS Server manually

Get TP-Link Archer D5 PDF manuals and user guides View all TP-Link Archer D5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Enable IPv6: Check this box to enable IPv6.  Default Gateway: Select a WAN connection from the drop-down list as the IPv4 default gateway.  IPv6 Default Gateway: Select a WAN connection from the drop-down list as the IPv6 default gateway. Click Advance, advanced selections for WAN Service Setup can be shown.  Service Name/Server Name: Enter the Service Name and Server Name if it was provided by your ISP. You can leave them blank, if the ISP doesn't provide them.  MTU (bytes): The default MTU (Maximum Transmission Unit) value is 1480 Bytes. Do not change the default value unless required by your ISP.  Enable Fullcone NAT: It is a type of NAT, if not enabled, the default NAT will act.  Enable SPI Firewall: The SPI firewall enhances network's security. Select the option to use a firewall, or else without a firewall.  Enable IGMP Proxy: IGMP (Internet Group Management Protocol) is used to manage multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for client devices, such as the modem router. It is enabled by default.  Use IP address specified by ISP: Select this option and enter the IP address provided by your ISP.  Set DNS Server manually: Choose "Set DNS Server manually", you can set DNS Server manually here. The modem router will use this DNS Server for priority.  Use IPv6 address specified by ISP: Choose "Use IPv6 address specified by ISP", you can enter the IPv6 address provided by your ISP.  Set IPv6 DNS Server manually: Choose "Set IPv6 DNS Server manually", you can set IPv6 DNS Server manually here. The modem router will use this IPv6 DNS Server for priority. Click the Save button to save the settings. 4.5.1.4 PPPoA If your ISP provides a PPPoA connection and you need to use an ATM Interface, choose PPPoA in the drop-down list, and then the screen will be displayed as below. The configuration is similar to PPPoE. Please refer to the section 4.5.1.3 PPPoE to configure this part. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
Archer
D5
AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
27
Enable IPv6:
Check this box to enable IPv6.
Default Gateway:
Select a WAN connection from the drop-down list as the IPv4 default
gateway.
IPv6 Default Gateway:
Select a WAN connection from the drop-down list as the IPv6 default
gateway.
Click
Advance
, advanced selections for WAN Service Setup can be shown.
Service Name/Server Name
: Enter the Service Name and Server Name if it was provided by
your ISP. You can leave them blank, if the ISP doesn’t provide them.
MTU (bytes):
The default
MTU
(Maximum Transmission Unit) value is 1480 Bytes. Do not
change the default value unless required by your ISP.
Enable Fullcone NAT
: It is a type of NAT, if not enabled, the default NAT will act.
Enable SPI Firewall:
The SPI firewall enhances network’s security. Select the option to use a
firewall, or else without a firewall.
Enable
IGMP Proxy
: IGMP (Internet Group Management Protocol) is used to manage
multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for
client devices, such as the modem router. It is enabled by default.
Use IP address specified by ISP:
Select this option and enter the IP address provided by
your ISP.
Set DNS Server manually:
Choose
“Set DNS Server manually”, you can set DNS Server
manually here. The modem router will use this DNS Server for priority.
Use IPv6 address specified by ISP:
Choose “Use IPv6 address specified by ISP”, you can
enter the IPv6 address provided by your ISP.
Set IPv6 DNS Server manually:
Choose
“Set IPv6 DNS Server manually”, you can set IPv6
DNS Server manually here. The modem router will use this IPv6 DNS Server for priority.
Click the
Save
button to save the settings.
4.5.1.4 PPPoA
If your ISP provides a
PPPoA
connection and you need to use an ATM Interface, choose
PPPoA
in the drop-down list, and then the screen will be displayed as below.
The configuration is similar to
PPPoE
. Please refer to the section
4.5.1.3 PPPoE
to configure this
part.