TP-Link Auranet EAP120 EAP Controller V2.2.3 User Guide - Page 38

Access Control, Wireless Control > Access Control., Apply

Get TP-Link Auranet EAP120 PDF manuals and user guides View all TP-Link Auranet EAP120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

3.2 Access Control Access Control is used to block or allow the clients to access specific subnets. To configure Access Control rules, follow the steps below. 1. Go to Wireless Control > Access Control. 2. Click to add a new Access Control rule. 3. Configure the following parameters. Rule Name Specify a name for this rule. Rule Mode Select the mode for this rule. Block: Select this mode to block the rule members to access the network. Allow: Select this mode to allow the rule members to access the network. Rule Memebers Subnets: Clients of the subnet will be controlled by the rule. Enter the subnet for this rule in the format X.X.X.X/X and click . Up to 16 subnets can be added. Except Subnets: Clients of the subnet will be controlled by the rule. Enter the subnet that does not follow this rule in the format X.X.X.X/X and click . Up to 16 subnets can be added. The rule will not apply to the subnets that is in both the Subnets list and the Except Subnets list. 4. Click Apply to save the configurations. 5. Go to Wireless Settings > Basic Wireless Setting and enable Access Control function of a selected SSID. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
33
3.2
Access Control
Access Control is used to block or allow the clients to access specific subnets. To configure
Access Control rules, follow the steps below.
1. Go to
Wireless Control > Access Control.
2. Click
to add a new Access Control rule.
3. Configure the following parameters.
Rule Name
Specify a name for this rule.
Rule Mode
Select the mode for this rule.
Block
: Select this mode to block the rule members to access the network.
Allow
: Select this mode to allow the rule members to access the network.
Rule Memebers
Subnets
: Clients of the subnet will be controlled by the rule. Enter the subnet for this
rule in the format X.X.X.X/X and click
. Up to 16 subnets can be added.
Except Subnets
: Clients of the subnet will be controlled by the rule. Enter the subnet
that does not follow this rule in the format X.X.X.X/X and click
. Up to 16
subnets can be added.
The rule will not apply to the subnets that is in both the Subnets list and the Except
Subnets list.
4. Click
Apply
to save the configurations.
5. Go to
Wireless Settings > Basic Wireless Setting
and enable Access Control function of
a selected SSID.