Home » TP-Link Manuals » Hubs & Switches » TP-Link TL-SL5428E » Manual Viewer

TP-Link TL-SL5428E User Guide - Page 183

Primary IP, Secondary IP, Authentication Port, Authentication KEY, Accounting, Accounting Port,

UPC - 845973020873

Add to My Manuals
Save this manual to your list of manuals

Page 183 highlights

Primary IP: Secondary IP: Authentication Port: Authentication KEY: ¾ Accounting Config Accounting: Primary IP: Secondary IP: Accounting Port: Accounting Key: Enter the IP address of the authentication server. Enter the IP address of the alternate authentication server. Set the UDP port of authentication server(s). The default port is 1812 Set the shared password for the switch and the authentication servers to exchange messages. Enable/Disable the accounting feature. Enter the IP address of the accounting server. Enter the IP address of the alternate accounting server. Set the UDP port of accounting server(s). The default port is 1813. Set the shared password for the switch and the accounting servers to exchange messages. Note: 1. The 802.1X function takes effect only when it is enabled globally on the switch and for the port. 2. The 802.1X function can not be enabled for LAG member ports. That is, the port with 802.1X function enabled can not be added to the LAG. 3. The 802.1X function should not be enabled for the port connected to the authentication server. In addition, the authentication parameters of the switch and the authentication server should be the same. Configuration Procedure: Step Operation Description 1 Connect an authentication Required. Record the information of the client in the LAN to server to the switch and do the authentication server and configure the corresponding some configuration. authentication username and password for the client. 2 Install the 802.1X client Required. For the client computers, you are required to software. install the 802.1X software TpSupplicant provided on the CD. For the installation guide, please refer to Appendix C: 802.1X Client Software. 3 Configure the 802.1X Required. By default, the global 802.1X function is disabled. globally. On the Network Security→802.1X→Global Config page, configure the 802.1X function globally. 4 Configure the parameters of Required. On the Network Security→802.1X→Radius the authentication server Server page, configure the parameters of the server. 5 Configure the 802.1X for the Required. On the Network Security→802.1X→Port port. Config page, configure the 802.1X feature for the port of the switch basing on the actual network. Return to CONTENTS 175

Section	Page
Package Contents	9
Chapter 1 About this Guide	10
1.1 Intended Readers	10
1.2 Conventions	10
1.3 Overview of This Guide	10
Chapter 2 Introduction	14
2.3.1 Front Panel	15
2.3.2 Rear Panel	16
Chapter 3 Installation	17
3.1 Precautions	17
3.2 Installation	17
3.2.1 Desktop Installation	18
3.2.2 Rack Installation	18
3.3 Connect to Ground	19
Chapter 4 Connection	22
4.1 Ethernet Ports	22
4.2 SFP Ports	22
4.3 Console Port	23
4.4 Power On	24
Chapter 5 Login to the Switch	25
5.1 Login	25
5.2 Configuration	25
Chapter 6 System	27
6.1 System Info	27
6.1.1 System Summary	27
6.1.2 Device Description	29
6.1.3 System Time	30
6.1.4 System IP	31
6.2 User Manage	32
6.2.1 User Table	32
6.2.2 User Config	32
6.3 System Tools	34
6.3.1 Config Restore	34
6.3.2 Config Backup	34
6.3.3 Firmware Upgrade	35
6.3.4 System Reboot	36
6.3.5 System Reset	36
6.4 Access Security	36
6.4.1 Access Control	36
6.4.2 SSL Config	38
6.4.3 SSH Config	39
Chapter 7 Switching	45
7.1 Port	45
7.1.1 Port Config	45
7.1.2 Port Mirror	46
7.1.3 Port Security	48
7.2 LAG	49
7.2.1 LAG Table	50
7.2.2 Static LAG	51
7.2.3 LACP Config	52
7.3 Traffic Monitor	54
7.3.1 Traffic Summary	54
7.3.2 Traffic Statistics	55
7.4 MAC Address	56
7.4.1 Address Table	57
7.4.2 Static Address	59
7.4.3 Dynamic Address	60
7.4.4 Filtering Address	62
Chapter 8 VLAN	64
8.1 802.1Q VLAN	65
8.1.1 VLAN Config	67
8.1.2 Port Config	69
8.2 MAC VLAN	71
8.2.1 MAC VLAN	71
8.2.2 Port Enable	72
8.3 Protocol VLAN	73
8.3.1 Protocol VLAN	74
8.3.2 Protocol Template	74
8.3.3 Port Enable	75
8.4 VLAN VPN	76
8.4.1 VPN Config	77
8.4.2 VLAN Mapping	78
8.4.3 Port Enable	79
8.5 GVRP	80
Chapter 9 Spanning Tree	84
9.1 STP Config	89
9.1.1 STP Config	89
9.1.2 STP Summary	91
9.2 Port Config	92
9.3 MSTP Instance	94
9.3.1 Region Config	94
9.3.2 Instance Config	95
9.3.3 Instance Port Config	96
9.4 STP Security	98
9.4.1 Port Protect	98
9.4.2 TC Protect	101
9.5 Application Example for STP Function	102
Chapter 10 Multicast	106
10.1 IGMP Snooping	108
10.1.1 Snooping Config	109
10.1.2 Port Config	110
10.1.3 VLAN Config	111
10.1.4 Multicast VLAN	113
10.2 Multicast IP	116
10.2.1 Multicast IP Table	117
10.2.2 Static Multicast IP	117
10.3 Multicast Filter	118
10.3.1 IP-Range	119
10.3.2 Port Filter	120
10.4 Packet Statistics	121
Chapter 11 QoS	123
11.1 DiffServ	126
11.1.1 Port Priority	126
11.1.2 Schedule Mode	127
11.1.3 802.1P Priority	128
11.1.4 DSCP Priority	129
11.2 Bandwidth Control	131
11.2.1 Rate Limit	131
11.2.2 Storm Control	132
11.3 Voice VLAN	133
11.3.1 Global Config	135
11.3.2 Port Config	136
11.3.3 OUI Config	137
Chapter 12 ACL	139
12.1 Time-Range	139
12.1.1 Time-Range Summary	139
12.1.2 Time-Range Create	140
12.1.3 Holiday Config	141
12.2 ACL Config	141
12.2.1 ACL Summary	142
12.2.2 ACL Create	142
12.2.3 MAC ACL	143
12.2.4 Standard-IP ACL	144
12.2.5 Extend-IP ACL	145
12.3 Policy Config	146
12.3.1 Policy Summary	146
12.3.2 Policy Create	147
12.3.3 Action Create	147
12.4 Policy Binding	149
12.4.1 Binding Table	149
12.4.2 Port Binding	149
12.4.3 VLAN Binding	150
Chapter 13 Network Security	154
13.1 IP-MAC Binding	154
13.1.1 Binding Table	154
13.1.2 Manual Binding	155
13.1.3 ARP Scanning	157
13.1.4 DHCP Snooping	158
13.2 ARP Inspection	164
13.2.1 ARP Detect	168
13.2.2 ARP Defend	169
13.2.3 ARP Statistics	170
13.5 802.1X	175
13.5.1 Global Config	179
13.5.2 Port Config	181
13.5.3 Radius Server	182
Chapter 14 SNMP	184
14.1 SNMP Config	186
14.1.1 Global Config	186
14.1.2 SNMP View	187
14.1.3 SNMP Group	188
14.1.4 SNMP User	189
14.1.5 SNMP Community	191
14.2 Notification	193
14.3 RMON	195
14.3.1 History Control	196
14.3.2 Event Config	196
14.3.3 Alarm Config	197
Chapter 15 Cluster	200
15.1 NDP	201
15.1.1 Neighbor Info	201
15.1.2 NDP Summary	202
15.1.3 NDP Config	204
15.2 NTDP	205
15.2.1 Device Table	205
15.2.2 NTDP Summary	206
15.2.3 NTDP Config	208
15.3 Cluster	209
15.3.1 Cluster Summary	209
15.3.2 Cluster Config	212
15.3.3 Member Config	214
15.3.4 Cluster Topology	215
15.4 Application Example for Cluster Function	217
Chapter 16 Maintenance	220
16.1 System Monitor	220
16.1.1 CPU Monitor	220
16.1.2 Memory Monitor	221
16.2 Log	222
16.2.1 Log Table	223
16.2.2 Local Log	223
16.2.3 Remote Log	224
16.2.4 Backup Log	225
16.3 Device Diagnose	226
16.3.1 Cable Test	226
16.3.2 Loopback	227
16.4 Network Diagnose	227
16.4.1 Ping	227
16.4.2 Tracert	228
Chapter 17 System Maintenance via FTP	230
Appendix A: Specifications	235
Appendix B: Configuring the PCs	236
Appendix C: 802.1X Client Software	239

Match case Limit results 1 per page

175

Primary IP:

Enter the IP address of the authentication server.

Secondary IP:

Enter the IP address of the alternate authentication server.

Authentication Port:

Set the UDP port of authentication server(s). The default port is 1812

Authentication KEY:

Set the shared password for the switch and the authentication

servers to exchange messages.

Accounting Config

Accounting:

Enable/Disable the accounting feature.

Primary IP:

Enter the IP address of the accounting server.

Secondary IP:

Enter the IP address of the alternate accounting server.

Accounting Port:

Set the UDP port of accounting server(s). The default port is 1813.

Accounting Key:

Set the shared password for the switch and the accounting

servers to exchange messages.

Note:

1. The 802.1X function takes effect only when it is enabled globally on the switch and for the port.

2. The 802.1X function can not be enabled for LAG member ports. That is, the port with 802.1X

function enabled can not be added to the LAG.

3. The 802.1X function should not be enabled for the port connected to the authentication server.

In addition, the authentication parameters of the switch and the authentication server should

be the same.

Configuration Procedure:

Step

Operation

Description

Connect an authentication

server to the switch and do

some configuration.

Required. Record the information of the client in the LAN to

the authentication server and configure the corresponding

authentication username and password for the client.

Install

the

802.1X

client

software.

Required. For the client computers, you are required to

install the 802.1X software TpSupplicant provided on the

CD. For the installation guide, please refer to

Appendix C:

802.1X Client Software

Configure

the

802.1X

globally.

Required. By default, the global 802.1X function is disabled.

On the

Network Security

→

802.1X

→

Global Config

page,

configure the 802.1X function globally.

Configure the parameters of

the authentication server

Required. On the

Network Security

→

802.1X

→

Radius

Server

page, configure the parameters of the server.

Configure the 802.1X for the

port.

Required.

the

Network

Security

→

802.1X

→

Port

Config

page, configure the 802.1X feature for the port of

the switch basing on the actual network.

Return to CONTENTS