Yamaha PM5000 Owner's Manual - Page 83

MIDI Control Change Program No. U25, MIDI Setting Parameter No. U26, Control Change

Get Yamaha PM5000 PDF manuals and user guides View all Yamaha PM5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

MIDI Control Change (Program No. U25) The functions in this section determine whether the PM5000 sends and receives control change commands, as well as whether NRPN will be enabled. Digital Control Section MIDI Setting (Parameter No. U26) This is the basic PM5000 setting for MIDI transmission and reception, including selection of the SINGLE or MULTI mode for program change transmission and reception. MIDI CTL CHG 1 Press [ENTER] after selecting the above display and a display like the one shown below will appear. Use the [INC] and [DEC] keys to select the required setting, then press the [ENTER] key. Control Change CTL:OFF NRPN NRPN:ON 2 Use the [INC] and [DEC] keys to turn the selected parameter ON (reception and transmission enabled) or OFF (reception and transmission disabled). CTL:ON 3 Set the other functions as required. MIDI SETTING 1 Press [ENTER] after selecting the above display and a display like the one shown below will appear. Use the [INC] and [DEC] keys to select the required setting, then press the [ENTER] key. RX CH (Receive Channel): Program change commands will be received on the specified channel. RX CH:10 TX CH (Transmit Channel): Program change commands will be transmitted on the specified channel. TX CH:10 OMNI: When ON program change commands can be received on all 16 MIDI channels. When OFF reception occurs only on the specified RX CH. OMNI:OFF MODE: When set to SINGLE operation is determined by the RX CH, BANK, and OMNI parameters. When set to MULTI the OMNI and BANK settings are ignored and both parameters are forced ON. MODE:MULTI BANK: Bank select numbers will be received when this parameter is ON. BANK:ON 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
81
Digital Control Section
MIDI Control Change (Program No. U25)
The functions in this section determine whether the
PM5000 sends and receives control change commands,
as well as whether NRPN will be enabled.
1
Press [ENTER] after selecting the above display and
a display like the one shown below will appear. Use
the [INC] and [DEC] keys to select the required
setting, then press the [ENTER] key.
Control Change
NRPN
2
Use the [INC] and [DEC] keys to turn the selected
parameter ON (reception and transmission enabled)
or OFF (reception and transmission disabled).
3
Set the other functions as required.
MIDI Setting (Parameter No. U26)
This is the basic PM5000 setting for MIDI transmission
and reception, including selection of the SINGLE or
MULTI mode for program change transmission and
reception.
1
Press [ENTER] after selecting the above display and
a display like the one shown below will appear. Use
the [INC] and [DEC] keys to select the required
setting, then press the [ENTER] key.
RX CH (Receive Channel):
Program change commands will be received on the
specified channel.
TX CH (Transmit Channel):
Program change commands will be transmitted on the
specified channel.
OMNI:
When ON program change commands can be received
on all 16 MIDI channels. When OFF reception occurs
only on the specified RX CH.
MODE:
When set to SINGLE operation is determined by the
RX CH, BANK, and OMNI parameters. When set to
MULTI the OMNI and BANK settings are ignored and
both parameters are forced ON.
BANK:
Bank select numbers will be received when this
parameter is ON.
MIDI CTL CHG
CTL:OFF
NRPN:ON
CTL:ON
MIDI SETTING
RX CH:10
TX CH:10
OMNI:OFF
MODE:MULTI
BANK:ON