Yamaha PM5000 Owner's Manual - Page 90

Appendix Internal Switch Settings For Each module As you tell from the PM5000 block diagram, each module has a number of internal switch settings. These settings can be changed to "customize" the PM5000 signal flow to most ideally suit your mixing requirements. The chart below lists the switches and their functions. In some cases two switches must be set appropriately to specify a function. When changing internal switch settings make only the necessary changes while referring to the block diagram. = initial factory settings. Module Target Switch No./ Switch No./ Setting Setting Selectable function Module Target MONO Input DIRECT SW105 OUT PRE SW106 n/a The direct out signal is pre-EQ (SW106 has no effect). POST PRE The direct out signal is post-EQ, pre-fader. POST POST The direct out signal is post-fader, post-on switch. AUX PRE SW107 FADER PRE POST The pre-fader aux signal is sent to the bus pre-EQ (PRE) or post-EQ (POST). STEREO Input AUX PRE SW106 FADER PRE POST The pre-fader aux signal is sent to the bus pre-EQ (PRE) or post-EQ (POST). Ø SW MODE (Phase SW Mode) SW105 L&R L ONLY Input signal phase inversion is applied to both stereo channels (L&R) or only the left channel (L ONLY). STEREO AUX MASTER Oddchannel ST AUX TO MATRIX SW102 PRE POST SW103 PRE PRE The odd-numbered channel ST AUX TO MATRIX signal is pre-fader, pre-on switch. The odd-numbered channel ST AUX TO MATRIX signal is post-fader, pre-on switch. Evenchannel ST AUX TO MATRIX SW105 PRE POST PRE POST The odd-numbered channel ST AUX TO PRE MATRIX signal is pre-fader, post-on switch. POST POST The odd-numbered channel ST AUX TO MATRIX signal is post-fader, post-on switch. POST G/A MASTER Oddchannel G/A TO MATRIX SW102 PRE POST SW103 PRE PRE The odd-numbered channel G/A TO MATRIX signal is pre-fader, pre-on switch. The odd-numbered channel G/A TO MATRIX signal is post-fader, pre-on switch. SW105 PRE POST PRE POST The odd-numbered channel G/A TO PRE MATRIX signal is pre-fader, post-on switch. POST POST The odd-numbered channel G/A TO MATRIX signal is post-fader, post-on switch. POST Oddchannel G/A TO STEREO SW101 PRE POST The odd-numbered channel G/A TO STEREO signal is pre-on switch (PRE) or post-on switch (POST). Evenchannel G/A TO STEREO PRE POST ST L TO SW102 MONO MATRIX MASTER PRE SW103 PRE The left-channel TO MATRIX signal is prefader, pre-on switch. R TO MATRIX SW105 PRE POST PRE The left-channel TO MATRIX signal is post-fader, pre-on switch. POST PRE POST The left-channel TO MATRIX signal is pre- PRE fader, post-on switch. POST POST The left-channel TO MATRIX signal is post-fader, post-on switch. POST Switch No./ Setting Switch No./Setting SW106 PRE PRE POST POST SW106 PRE PRE POST POST The even-numbered channel ST AUX TO MATRIX signal is pre-fader, pre-on switch. The even-numbered channel ST AUX TO MATRIX signal is post-fader, pre-on switch. The even-numbered channel ST AUX TO MATRIX signal is pre-fader, post-on switch. The even-numbered channel ST AUX TO MATRIX signal is post-fader, post-on switch. The even-numbered channel G/A TO MATRIX signal is pre-fader, pre-on switch. The even-numbered channel G/A TO MATRIX signal is post-fader, pre-on switch. The even-numbered channel G/A TO MATRIX signal is pre-fader, post-on switch. The even-numbered channel G/A TO MATRIX signal is post-fader, post-on switch. SW106 PRE PRE POST POST The even-numbered channel G/A TO STEREO signal is pre-on switch (PRE) or post-on switch (POST). The right-channel TO MATRIX signal is pre-fader, pre-on switch. The right-channel TO MATRIX signal is post-fader, pre-on switch. The right-channel TO MATRIX signal is pre-fader, post-on switch. The right-channel TO MATRIX signal is post-fader, post-on switch. 88