Yamaha PM5000 Owner's Manual - Page 98

Appendix Specifications 1. General Specifications 0dBu is referenced to 0.775 Vrms. Total Harmonic Distortion (Master Output) Less than 0.1% (THD+N) 20Hz-20kHz @ +14dBu 600Ω (Input Gain Control at Maximum) Frequency Response (Master Output) 0+1,-3dB 20Hz-20kHz @ +4dBu 600Ω (Input Gain Control at Maximum) Hum & Noise (20Hz-20kHz) *1 -128dBu Equivalent Input Noise. Rs=150Ω -100dBu Residual Output Noise. Input Gain=Maximum -92dBu (96dB S/N) STEREO AUX Master fader at nominal level and all assign SW's off. Input Pad =OFF -87dBu (91dB S/N) GROUP/AUX Master fader at nominal level and all assign SW's off. Input sensitivity=-60dBu -92dBu (96dB S/N) STEREO, MONO (C) Master fader at nominal level and all assign SW's off. -64dBu (68dB S/N) STEREO AUX, GROUP/AUX, STEREO, MONO (C) Master fader and one input fader at nominal level. -89dBu(93dB S/N) MATRIX Master at nominal level and all Matrix mix controls at minimum level. Maximum Voltage Gain *2 64dB MONO IN to MONO IN INSERT OUT,DIRECT OUT (pre fader) 80dB MONO IN to STEREO AUX OUT (PRE),GROUP/AUX OUT (AUX mode & PRE) 90dB MONO IN to STEREO AUX OUT (POST),GROUP/AUX OUT (AUX mode & POST) 84dB MONO IN to GROUP/AUX OUT (GROUP mode), STEREO OUT(INPUT to ST), MONO (C) OUT (INPUT to MONO) 90dB MONO IN to MATRIX OUT (GROUP/AUX MASTER GROUP mode to MATRIX) 64dB ST IN to ST INSERT OUT 80dB ST IN to STEREO AUX OUT (PRE) 90dB ST IN to STEREO AUX OUT (POST) 84dB ST IN to GROUP/AUX OUT (GROUP mode), STEREO OUT (INPUT to ST) 81dB ST IN to MONO (C) OUT (INPUT to MONO) 77dB ST IN to GROUP/AUX OUT (AUX mode & PRE) 87dB ST IN to GROUP/AUX OUT (AUX mode & POST) 10dB SUB IN to Master OUT 6dB 2TR IN to MONITOR OUT Crosstalk -80dB @ 1kHz, -70dB @ 10kHz Adjacent inputs. -80dB @ 1kHz, -70dB @ 10kHz input to output.(except between L and R) MONO & ST INPUT PAD 26dB MONO & ST INPUT GAIN 50dB Variable INPUT High Pass Filter 12dB/octave roll off below 20-400Hz at -3dB points. INPUT Equalization *3 +15, -15dB maximum HIGH 1k-20kHz (peaking/shelving, Q=0.5-3) HI-MID 0.4k-8kHz (peaking, Q=0.5-3) LO-MID 80-1.6kHz (peaking, Q=0.5-3) LOW 30-600Hz (peaking/shelving, Q=0.5-3) Sweep sine wave oscillator/Pink noise with burst 4 mode selectable (100Hz/1kHz/10kHz/PINK) Selectable FIX or SWEEP for 100Hz/1kHz/10kHz by SWEEP/BURST ON/OFF switch, sweep range: x0.2-x2, Less than 1% T.H.D. @ +4dBu Selectable continue or BURST for PINK noise by SWEEP/BURST ON/OFF switch. PINK NOISE: fixed 200msec, INTERVAL: variable 1sec-20sec Phantom Power +48VDC is applied to balanced inputs for powering condenser microphones via 6.8kΩ currentlimiting/isolation resistors. Input LED Meter 9-points (PEAK/+12/+6/+3/0/-3/-6/-12/-25dB) LED level meter built into each MONO-IN and STIN module. PEAK LED (red) turns on when pre-EQ level or post-EQ level or pre-Fader level reaches 3dB below clipping. +12/+6/+3/0 LED (yellow) turns on when pre-Fader level reaches +12/+6/+3/0dB. -3/-6/-12/-25 LED (green) turns on when pre-Fader level reaches -3/-6/-12/-25dB. Output LED Meter 20-points (PEAK, +15, , -39dB) LED level meter. STEREO AUX 1 (L, R)-12 (L, R), STEREO MATRIX 1 (L, R)-4 (L, R) (STEREO AUX/STEREO MATRIX selectable) GROUP/AUX 1-8, MATRIX 1-8 (GROUP/AUX, MATRIX selectable) STEREO (L, R), MONO (C) CUE (L, R, C), TB/OSC (CUE C, TB/OSC automatic select) PEAK LED (red) turns on when pre-LineAmp level reaches 3dB below clipping. +15/··/0 LED (yellow) turns on when pre-LineAmp level reaches +15//0dB. -3/··/-39 LED (green) turns on when pre-LineAmp level reaches -3//-39dB. 96