ZyXEL Omni TA 128 User Guide - Page 115

DTE Port 2 Call Control

Get ZyXEL Omni TA 128 PDF manuals and user guides View all ZyXEL Omni TA 128 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 115 highlights

DTE Port 2 Call Control To place a call through DTE port 2, use the ATDxxxx command. If the Calling Party Number (the original address) is required in the outgoing SETUP message, it can be pre-stored using the AT&ZOI=xxxx command. Once the PPP connection is established, the TA128 will indicate the connection message with DTE speed as follows: CONNECT 115200 PPP Use ATV0, if numerical result code is required. An X.75 or V.120 can be placed after selecting the protocol using ATBnn. By default, to answer a call through DTE port 2, the MSN(or subaddress) must have been set using the AT&ZI5=xxxx command and the number xxxx must be matched with the Called Party Number (the destination address) of the incoming call. The DTE port 2 Multi-Auto function will automatically identify the protocol of the incoming call as PPP, X.75 or V.120. Use ATS87.7=1 to enable the TA to route data calls to DTE port 2 if DTE port 1 is busy. 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
103
DTE Port 2 Call Control
To place a call through DTE port 2, use the ATDxxxx command.
If the Calling Party Number (the original address) is required in the
outgoing SETUP message, it can be pre-stored using the
AT&ZOI=xxxx command. Once the PPP connection is
established, the TA128 will indicate the connection message with
DTE speed as follows:
CONNECT 115200 PPP
Use ATV0, if numerical result code is required. An X.75 or V.120
can be placed after selecting the protocol using ATBnn.
By default, to answer a call through DTE port 2, the MSN(or
subaddress) must have been set using the
AT&ZI5=xxxx
command and the number
xxxx
must be matched with the Called
Party Number (the destination address) of the incoming call. The
DTE port 2 Multi-Auto function will automatically identify the
protocol of the incoming call as PPP, X.75 or V.120.
Use ATS87.7=1 to enable the TA to route data calls to DTE port 2
if DTE port 1 is busy.