ZyXEL Omni TA 128 User Guide - Page 96

Placing a Call

Get ZyXEL Omni TA 128 PDF manuals and user guides View all ZyXEL Omni TA 128 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

• ATCN - When and only when the type-of-number denotes a national number will this "Prefix" be added to the Calling-party-number before indicating it to the DTE. • ATCN - Disable the national number prefix-adding function. (Default) O NOTE: The angle brackets '' are part of this command. Disable inbound call connection In some cases, the user may desire the TA128 to not answer any incoming calls. This can be done by setting the bit 0 of S-register S118: • S118.0=0 - Enable the TA128 to answer a call (by default). • S118.0=1 - Disable the TA128 to answer any call. Point-to-Point Configuration In some areas, since Direct-Dial-In (DDI) number is less expensive than MSN, users may want to subscribe to point-to-point ISDN to employ the DDI function. In this case, only one TA can be connected to the ISDN line and the TEI (Terminal Equipment Identifier) is always ZERO. This can be done by setting the bit 1 of S-register S119: S119.1 = 0 - Disable point-to-point DDI function (default). S119.1 = 1 - Enable point-to-point DDI function. Placing a Call To initiate a call, configure the TA128 according to the Bearer Service (or protocol) you want to use. • ATBnn - for ISDN data calls. 84

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
84
•
ATCN<
Prefix> - When and only when the type-of-number
denotes a national number will this "Prefix" be added to the
Calling-party-number before indicating it to the DTE.
•
ATCN<>
- Disable the national number prefix-adding function.
(Default)
O
NOTE
:
The angle brackets '<' and '>' are part of
this command.
Disable inbound call connection
In some cases, the user may desire the TA128 to
not
answer any
incoming calls. This can be done by setting the bit 0 of S-register
S118:
•
S118.0=0
- Enable the TA128 to answer a call (by default).
•
S118.0=1
- Disable the TA128 to answer any call.
Point-to-Point Configuration
In some areas, since Direct-Dial-In (DDI) number is less expensive
than MSN, users may want to subscribe to point-to-point ISDN to
employ the DDI function. In this case, only one TA can be
connected to the ISDN line and the TEI (Terminal Equipment
Identifier) is always ZERO. This can be done by setting the bit 1 of
S-register S119:
S119.1 = 0 - Disable point-to-point DDI function (default).
S119.1 = 1 - Enable point-to-point DDI function.
Placing a Call
To initiate a call, configure the TA128 according to the Bearer
Service (or protocol) you want to use.
•
ATBnn
- for ISDN data calls.