Home » ZyXEL Manuals » Networking » ZyXEL VES1724-56 » Manual Viewer

ZyXEL VES1724-56 User Guide - Page 56

VDSL Port Status Change

Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Chapter 7 System Status and Port Statistics The following table describes the labels in this screen. Table 6 Port Status LABEL Port Name Link State LACP TxPkts RxPkts Errors Tx KB/s Rx KB/s Up Time Retrain Clear Counter DESCRIPTION This identifies a VDSL or Ethernet port. Click a port number to display the Port Details screen (refer to Figure 35 on page 70). This is the name you assigned to this port in the Basic Setting > Port Setup screen. For an Ethernet port, this field displays the speed (either 10M for 10Mbps, 100M for 100Mbps or 1000M for 1000Mbps) and the duplex (F for full duplex or H for half). It also shows the cable type (Copper or Fiber) for the combo ports. For a VDSL port, this field displays the VDSL transmission rate on the port. For VDSL ports, this field displays Showtime when the VDSL connection is up. Otherwise, it displays Idle, Handshake or Training during the VDSL line establishment. If you perform a DELT test, this field will display LD_Testing or LD_DONE. See Section 7.2.1 on page 56 for more information. For Ethernet ports, if STP (Spanning Tree Protocol) is enabled, this field displays the STP state of the port (see Section 14.1 on page 160 for more information). If STP is disabled, this field displays FORWARDING if the link is up, otherwise, it displays STOP. This fields displays whether LACP (Link Aggregation Control Protocol) has been enabled on the port. This field shows the number of transmitted frames on this port. This field shows the number of received frames on this port. This field shows the number of received errors on this port. This field shows the number of kilobytes per second transmitted on this port. This field shows the number of kilobytes per second received on this port. This field shows the total amount of time in hours, minutes and seconds the port has been up. Click Retrain to re-establish the line connection. Select Port, enter a port number and then click Clear Counter to erase the recorded statistical information for that port, or select Any to clear statistics for all ports. 7.2.1 VDSL Port Status Change The VDSL port status change is shown as the following flow chart. Only when the status is "Showtime", the VDSL connection is up. 56 VES1724-56 User's Guide

Section	Page
VES1724-56	1
Contents Overview	3
Table of Contents	5
User’s Guide	17
Getting to Know Your Switch	19
1.1 Introduction	19
1.2 Applications	19
1.2.1 MTU Application	19
1.2.2 Curbside Application	20
1.3 Ways to Manage the Switch	21
1.4 Good Habits for Managing the Switch	21
Hardware Installation and Connection	23
2.1 Installation Scenarios	23
2.2 Desktop Installation Procedure	23
2.3 Mounting the Switch on a Rack	24
2.3.1 Rack-mounted Installation Requirements	24
2.3.2 Attaching the Mounting Brackets to the Switch	24
2.3.3 Mounting the Switch on a Rack	25
2.4 Connecting the Frame Ground	25
Hardware Overview	27
3.1 Front Panel	27
3.1.1 Power Connector	27
3.1.2 Gigabit Ethernet Ports	28
3.1.3 Mini-GBIC Slots	29
3.1.4 Management Port	30
3.1.5 Console Port	31
3.1.6 ALARM Slot	31
3.2 LEDs	32
The Web Configurator	35
4.1 Introduction	35
4.2 System Login	35
4.3 The Port Status Screen	36
4.3.1 Change Your Password	41
4.4 Saving Your Configuration	41
4.5 Switch Lockout	41
4.6 Resetting the Switch	42
4.6.1 Reload the Configuration File	42
4.7 Logging Out of the Web Configurator	43
4.8 Help	43
Initial Setup Example	44
5.1 Overview	44
5.2 Configuring Switch Management IP Address	44
5.2.1 Creating a VLAN	45
5.2.2 Setting Port VID	46
Tutorials	48
6.1 How to Use DHCP Relay Per VLAN on the Switch	48
6.1.1 DHCP Relay Tutorial Introduction	48
6.1.2 Creating a VLAN	48
6.1.3 Configuring Management IP Address	50
6.1.4 Configuring DHCP VLAN Settings	51
6.1.5 Testing the Connection	52
Technical Reference	53
System Status and Port Statistics	55
7.1 Overview	55
7.2 Port Status Summary	55
7.2.1 VDSL Port Status Change	56
7.2.2 VDSL Port Details	57
7.2.3 VDSL Summary	67
7.2.4 VTUR Counter	68
7.2.5 Port Details	70
Basic Setting	73
8.1 Overview	73
8.2 System Information	74
8.3 General Setup	76
8.4 Introduction to VLANs	77
8.5 Switch Setup Screen	78
8.6 IPv6 Introduction	79
8.6.1 IPv6 Addressing	80
8.6.2 IPv6 Prefix and Prefix Length	80
8.6.3 IPv6 Subnet Masking	80
8.6.4 Interface ID	80
8.6.5 Link-local Address	80
8.6.6 Global Address	81
8.6.7 Unspecified	81
8.6.8 EUI-64	81
8.6.9 Stateless Autoconfiguration	81
8.7 IP Setup	82
8.7.1 Management IP Addresses	82
8.7.2 IPv6 Setup	85
8.8 Port Setup	87
8.9 Remote CPE Configuration	89
8.9.1 Remote CPE Configuration Information	95
8.10 Rate Limit Profile Setup	95
8.10.1 Per Queue Ratelimit Profile	97
8.11 Hardware Alarm Profile	98
VDSL Setup	99
9.1 VDSL Overview	99
9.1.1 VDSL Profile Example	103
9.1.2 Primary and Fallback VDSL Templates Example	104
9.2 VDSL Line Setup	105
9.3 VDSL Template Setup	106
9.3.1 VDSL Line Profile Setup	108
9.3.2 VDSL Line Profile Setup > Rate Adaptive	111
9.3.3 VDSL Line Profile Setup > MIB PSD Mask	113
9.3.4 VDSL Line Profile Setup > DPBO	114
9.3.5 VDSL Line Profile Setup > RFI Band	115
9.3.6 VDSL Line Profile Setup > Virtual Noise	117
9.3.7 VDSL Channel Profile Setup	118
9.3.8 VDSL G.INP Setup	120
9.3.9 VDSL INM Profile Setup	121
9.4 VDSL Alarm Template Setup	123
9.4.1 VDSL Line Alarm Profile Setup	124
9.4.2 VDSL Channel Alarm Profile Setup	126
VLAN	129
10.1 Introduction to IEEE 802.1Q Tagged VLANs	129
10.1.1 Forwarding Tagged and Untagged Frames	129
10.1.2 VLAN Tagging Priority	130
10.2 Automatic VLAN Registration	130
10.2.1 GARP	130
10.2.2 GVRP	130
10.3 Port VLAN Trunking	131
10.4 Select the VLAN Type	131
10.5 Static VLAN	132
10.5.1 Static VLAN Status	132
10.5.2 VLAN Details	133
10.5.3 Configure a Static VLAN	134
10.5.4 Configure a VLAN Profile	135
10.5.5 Configure VLAN Port Settings	137
10.6 Subnet Based VLANs	138
10.7 Configuring Subnet Based VLAN	139
10.8 Protocol Based VLANs	141
10.9 Configuring Protocol Based VLAN	142
10.10 Create an IP-based VLAN Example	143
10.11 Configuring MAC Based VLAN	144
10.12 Port Based VLAN Setup	146
10.12.1 Configure a Port Based VLAN	147
10.13 VLAN Counter	150
Static MAC Forward Setup	152
11.1 Overview	152
11.2 Configuring Static MAC Forwarding	152
Static Multicast Forward Setup	154
12.1 Static Multicast Forwarding Overview	154
12.2 Configuring Static Multicast Forwarding	155
Filtering	158
13.1 Configure a Filtering Rule	158
Spanning Tree Protocol	160
14.1 STP/RSTP Overview	160
14.1.1 STP Terminology	160
14.1.2 How STP Works	161
14.1.3 STP Port States	161
14.1.4 Multiple RSTP	162
14.1.5 Multiple STP	162
14.2 Spanning Tree Protocol Status Screen	165
14.3 Spanning Tree Configuration	165
14.4 Configure Rapid Spanning Tree Protocol	166
14.5 Rapid Spanning Tree Protocol Status	167
14.6 Configure Multiple Rapid Spanning Tree Protocol	168
14.7 Multiple Rapid Spanning Tree Protocol Status	170
14.8 Configure Multiple Spanning Tree Protocol	171
14.9 Multiple Spanning Tree Protocol Status	173
Broadcast Storm Control	176
15.1 Broadcast Storm Control Setup	176
Mirroring	178
16.1 Port Mirroring Setup	178
Link Aggregation	180
17.1 Link Aggregation Overview	180
17.2 Dynamic Link Aggregation	180
17.2.1 Link Aggregation ID	181
17.3 Link Aggregation Status	181
17.4 Link Aggregation Setting	182
17.5 Link Aggregation Control Protocol	183
17.6 Static Trunking Example	184
Port Authentication	186
18.1 Port Authentication Overview	186
18.1.1 IEEE 802.1x Authentication	186
18.1.2 MAC Authentication	187
18.2 Port Authentication Configuration	188
18.2.1 Activate IEEE 802.1x Security	188
18.2.2 Activate MAC Authentication	189
MAC Limit	191
19.1 MAC Limit Overview	191
19.2 MAC Limit	191
19.2.1 Mac Limit: Port Security	191
19.2.2 MAC Limit: VLAN Security	193
Classifier	194
20.1 About the Classifier and QoS	194
20.2 Configuring the Classifier	194
20.3 Viewing and Editing Classifier Configuration	197
20.4 Classifier Example	199
Policy Rule	200
21.1 Policy Rules Overview	200
21.1.1 DiffServ	200
21.1.2 DSCP and Per-Hop Behavior	200
21.2 Configuring Policy Rules	200
21.3 Policy Example	204
Queuing Method	205
22.1 Queuing Method Overview	205
22.1.1 Strictly Priority Queuing	205
22.1.2 Weighted Fair Queuing	205
22.1.3 Weighted Round Robin Scheduling (WRR)	205
22.2 Configuring Queuing	206
VLAN Stacking	208
23.1 VLAN Stacking Overview	208
23.1.1 VLAN Stacking Example	208
23.2 VLAN Stacking Port Roles	209
23.3 VLAN Tag Format	210
23.3.1 Frame Format	210
23.4 Configuring VLAN Stacking	211
23.4.1 Port-based Q-in-Q	212
23.4.2 Selective Q-in-Q	214
23.4.3 Port-based InnerQ	215
Multicast	217
24.1 Multicast Overview	217
24.1.1 IP Multicast Addresses	217
24.1.2 IGMP Filtering	217
24.1.3 IGMP Snooping	217
24.1.4 IGMP Snooping and VLANs	218
24.1.5 IGMP Proxy	218
24.1.6 Multicast Listener Discovery	218
24.1.7 MLD Messages	218
24.2 Multicast Status	219
24.3 Multicast Setting	221
24.4 IGMP Snooping VLAN	223
24.5 IGMP Filtering Profile	224
24.6 MVR Overview	225
24.6.1 Types of MVR Ports	226
24.6.2 MVR Modes	226
24.6.3 How MVR Works	226
24.7 General MVR Configuration	227
24.8 MVR Group Configuration	229
24.8.1 MVR Configuration Example	230
Authentication and Accounting	233
25.1 Authentication, Authorization and Accounting	233
25.1.1 Local User Accounts	233
25.1.2 RADIUS and TACACS+	234
25.2 Authentication and Accounting Screens	234
25.2.1 RADIUS Server Setup	234
25.2.2 TACACS+ Server Setup	237
25.2.3 Authentication and Accounting Setup	239
25.2.4 Vendor Specific Attribute	241
25.3 Supported RADIUS Attributes	242
25.3.1 Attributes Used for Authentication	242
25.3.2 Attributes Used for Accounting	243
IP Source Guard	246
26.1 IP Source Guard Overview	246
26.1.1 DHCP Snooping Overview	246
26.1.2 ARP Inspection Overview	248
26.2 IP Source Guard	250
26.3 IP Source Guard Static Binding	250
26.4 DHCP Snooping	252
26.5 DHCP Snooping Configure	254
26.5.1 DHCP Snooping Port Configure	256
26.5.2 DHCP Snooping VLAN Configure	257
26.6 ARP Inspection Status	258
26.6.1 ARP Inspection VLAN Status	260
26.6.2 ARP Inspection Log Status	261
26.7 ARP Inspection Configure	262
26.7.1 ARP Inspection Port Configure	263
26.7.2 ARP Inspection VLAN Configure	265
Loop Guard	267
27.1 Loop Guard Overview	267
27.2 Loop Guard Setup	269
CFM	271
28.1 CFM Overview	271
28.1.1 How CFM Works	271
28.2 CFM MA	272
28.3 CFM MD	274
VLAN Mapping	275
29.1 VLAN Mapping Overview	275
29.1.1 VLAN Mapping Example	275
29.2 Enabling VLAN Mapping	276
29.3 Configuring VLAN Mapping	277
Layer 2 Protocol Tunneling	279
30.1 Layer 2 Protocol Tunneling Overview	279
30.1.1 Layer 2 Protocol Tunneling Mode	280
30.2 Configuring Layer 2 Protocol Tunneling	281
DoS Prevention	283
31.1 DoS Prevention Overview	283
31.2 Configuring DoS Prevention	283
PPPoE IA	285
32.1 PPPoE Intermediate Agent Overview	285
32.1.1 PPPoE Intermediate Agent Tag Format	285
32.1.2 Sub-Option Format	286
32.1.3 PPPoE IA Configuration Options	286
32.2 The PPPoE IA Status Screen	287
32.3 PPPoE IA Global Configuration	287
32.4 PPPoE IA VLAN Configuration	288
SFP Threshold	291
33.1 SFP Threshold Setup	291
33.1.1 SFP Status	292
Static Route	295
34.1 Static Routing Overview	295
34.2 Configuring Static Routing	296
Differentiated Services	298
35.1 DiffServ Overview	298
35.1.1 DSCP and Per-Hop Behavior	298
35.1.2 DiffServ Network Example	298
35.2 Two Rate Three Color Marker Traffic Policing	299
35.2.1 TRTCM-Color-blind Mode	300
35.2.2 TRTCM-Color-aware Mode	300
35.3 Activating DiffServ	300
35.3.1 Configuring 2-Rate 3 Color Marker Settings	301
35.4 DSCP-to-IEEE 802.1p Priority Settings	303
35.4.1 Configuring DSCP Settings	303
DHCP	305
36.1 DHCP Overview	305
36.1.1 DHCP Modes	305
36.1.2 DHCP Configuration Options	305
36.2 DHCP Status	305
36.3 DHCP Relay	306
36.3.1 DHCP Relay Agent Information	306
36.3.2 DHCP Relay Agent Information Format	306
36.3.3 Sub-Option Format	307
36.3.4 Configuring DHCP Global Relay	307
36.3.5 Global DHCP Relay Configuration Example	309
36.4 Configuring DHCP VLAN Settings	310
36.4.1 Example: DHCP Relay for Two VLANs	311
Maintenance	313
37.1 The Maintenance Screen	313
37.2 Firmware Upgrade	314
37.2.1 Dual Firmware Image	314
37.3 Restore a Configuration File	315
37.4 Backup a Configuration File	316
37.5 Load Factory Default	316
37.6 Save Configuration	317
37.7 Reboot System	317
37.8 FTP Command Line	317
37.8.1 Filename Conventions	317
37.8.2 FTP Command Line Procedure	318
37.8.3 GUI-based FTP Clients	319
37.8.4 FTP Restrictions	319
Access Control	320
38.1 Access Control Overview	320
38.2 The Access Control Main Screen	320
38.3 About SNMP	320
38.3.1 SNMP v3 and Security	321
38.3.2 Supported MIBs	322
38.3.3 SNMP Traps	322
38.3.4 Configuring SNMP	326
38.3.5 Configuring SNMP Trap Group	328
38.3.6 Setting Up Login Accounts	328
38.4 SSH Overview	330
38.5 How SSH works	330
38.6 SSH Implementation on the Switch	331
38.6.1 Requirements for Using SSH	331
38.7 Introduction to HTTPS	331
38.8 HTTPS Example	332
38.8.1 Internet Explorer Warning Messages	332
38.8.2 Mozilla Firefox Warning Messages	335
38.8.3 Netscape Navigator Warning Messages	336
38.8.4 The Main Screen	337
38.9 Service Port Access Control	338
38.10 Remote Management	339
Diagnostic	341
39.1 Diagnostic	341
Syslog	342
40.1 Syslog Overview	342
40.2 Syslog Setup	343
40.3 Syslog Server Setup	344
Loop Diagnostic	345
41.1 Dual-End Loop Test	345
41.2 Single-End Loop Test (SELT)	347
MAC Table	349
42.1 MAC Table Overview	349
42.2 Viewing the MAC Table	350
ARP Table	351
43.1 ARP Table Overview	351
43.1.1 How ARP Works	351
43.2 Viewing the ARP Table	351
Hardware Information	353
44.1 Hardware Information	353
CFM Action	354
45.1 CFM Action	354
IPv6 Cache	356
46.1 Overview	356
46.2 Neighbor Cache	357
46.3 Prefix List	358
46.4 Destination Cache	359
46.5 Route List	360
46.6 Default Router List	361
Troubleshooting	363
47.1 Power, Hardware Connections, and LEDs	363
47.2 Switch Access and Login	364
47.3 Switch Configuration	366
Product Specifications	367
Common Services	383
Legal Information	387

Match case Limit results 1 per page

Chapter 7 System Status and Port Statistics

VES1724-56 User’s Guide

The following table describes the labels in this screen.

7.2.1

VDSL Port Status Change

The VDSL port status change is shown as the following flow chart. Only when the status is

"Showtime", the VDSL connection is up.

Table 6

Port Status

LABEL

DESCRIPTION

Port

This identifies a VDSL or Ethernet port. Click a port number to display the

Port Details

screen (refer to

Figure 35 on page 70

Name

This is the name you assigned to this port in the

Basic Setting

Port Setup

screen.

Link

For an Ethernet port, this field displays the speed (either

10M

for 10Mbps,

100M

for

100Mbps or

1000M

for 1000Mbps) and the duplex (

for full duplex or

for half). It also

shows the cable type (

Copper

Fiber

) for the combo ports.

For a VDSL port, this field displays the VDSL transmission rate on the port.

State

For VDSL ports, this field displays

Showtime

when the VDSL connection is up. Otherwise, it

displays

Idle

Handshake

Training

during the VDSL line establishment. If you perform

a DELT test, this field will display

LD_Testing

LD_DONE

. See

Section 7.2.1 on page 56

for more information.

For Ethernet ports, if STP (Spanning Tree Protocol) is enabled, this field displays the STP

state of the port (see

Section 14.1 on page 160

for more information). If STP is disabled,

this field displays

FORWARDING

if the link is up, otherwise, it displays

STOP

LACP

This fields displays whether LACP (Link Aggregation Control Protocol) has been enabled on

the port.

TxPkts

This field shows the number of transmitted frames on this port.

RxPkts

This field shows the number of received frames on this port.

Errors

This field shows the number of received errors on this port.

Tx KB/s

This field shows the number of kilobytes per second transmitted on this port.

Rx KB/s

This field shows the number of kilobytes per second received on this port.

Up Time

This field shows the total amount of time in hours, minutes and seconds the port has been

up.

Retrain

Click

Retrain

to re-establish the line connection.

Clear Counter

Select

Port

, enter a port number and then click

Clear Counter

to erase the recorded

statistical information for that port, or select

Any

to clear statistics for all ports.