Compaq AP200 Reference Guide - Page 101

Connecting to an Ethernet Network, Attaching a Network Cable to the RJ-45 Connector

Get Compaq AP200 - Professional - 128 MB RAM PDF manuals and user guides
UPC - 743172868534
View all Compaq AP200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

5-2 Network Communications Connecting to an Ethernet Network An RJ-45 Ethernet network connector is included on your workstation. Attaching a Network Cable to the RJ-45 Connector Refer to the following illustration to connect a network cable to the RJ-45 connector. IMPORTANT: If you are connecting to a 100BaseTX network, you must use a Category 5 UTP cable. Also, in order for Remote Wakeup and Remote Shutdown to function, the internal power cable for the network interface controller must be connected to the system board. See the section "Remote Wakeup and Remote Shutdown" in Chapter 3 for information on these features. WARNING: To reduce the risk of injury from electrical shock, remove all power cords to completely disconnect power from the system before attaching the network cable to the RJ-45 connector. Figure 5-1. Attaching the network cable to the RJ-45 connector

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
5-2
Network Communications
Connecting to an Ethernet Network
An RJ-45 Ethernet network connector is included on your workstation.
Attaching a Network Cable to the
RJ-45 Connector
Refer to the following illustration to connect a network cable to the RJ-45
connector.
IMPORTANT:
If you are connecting to a 100BaseTX network, you must use
a Category 5 UTP cable. Also, in order for Remote Wakeup and Remote
Shutdown to function, the internal power cable for the network interface
controller must be connected to the system board. See the section “Remote
Wakeup and Remote Shutdown” in Chapter 3 for information on these
features.
WARNING:
To reduce the risk of injury from
electrical shock, remove all power cords to
completely disconnect power from the system
before attaching the network cable to the RJ-45
connector.
Figure 5-1.
Attaching the network cable to the RJ-45 connector