Compaq AP200 Reference Guide - Page 152

Intelligent Manageability., Replace the workstation access panel.

Get Compaq AP200 - Professional - 128 MB RAM PDF manuals and user guides
UPC - 743172868534
View all Compaq AP200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 152 highlights

G-2 Clearing Configuration Memory 4. Locate the jumper labeled E50. 123 Figure G-1. Location of the E50 jumper and pins 1-3 on the system board 5. Remove the jumper from pins 1 and 2, place it on pins 2 and 3 for approximately 30 seconds, then return it to pins 1 and 2. 6. Replace the workstation access panel. 7. Reconnect the network cable and external devices. 8. Plug in the workstation and turn on power. NOTE: When the CMOS jumper is removed, your passwords will become invalid because the passwords are stored in the configuration memory. You will need to reset your passwords and any special system setups. See Chapter 3, "Intelligent Manageability."

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
G-2
Clearing Configuration Memory
4.
Locate the jumper labeled E50.
123
Figure G-1.
Location of the E50 jumper and pins 1-3 on the system board
5.
Remove the jumper from pins 1 and 2, place it on pins 2 and 3 for
approximately 30 seconds, then return it to pins 1 and 2.
6.
Replace the workstation access panel.
7.
Reconnect the network cable and external devices.
8.
Plug in the workstation and turn on power.
NOTE
:
When the CMOS jumper is removed, your passwords will become
invalid because the passwords are stored in the configuration memory. You
will need to reset your passwords and any special system setups. See Chapter
3, “Intelligent Manageability.”