Compaq AP200 Reference Guide - Page 115

Solving Hardware Installation Problems, Table 6-6

Get Compaq AP200 - Professional - 128 MB RAM PDF manuals and user guides
UPC - 743172868534
View all Compaq AP200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 115 highlights

6-13 Solving Hardware Installation Problems You may need to reconfigure the workstation when you add or remove hardware, such as an additional diskette drive. To reconfigure the workstation in Windows NT Workstation 4.0 after installing new hardware, run the Computer Setup utility. See Chapter 2, "Software," for more information on Computer Setup. Table 6-6 Solving Hardware Installation Problems Problem Cause A new device is not The workstation needs to be recognized as part of the reconfigured to recognize the workstation system device. Solution Follow the reconfiguration instructions above. Cable(s) of new external device are loose or power cables are unplugged. Ensure that all cables are properly and securely connected and that pins in the cable or connector are not bent down. Power switch of new external device is not turned on. Turn off the workstation, turn on the external device, then turn on the workstation to integrate the device with the workstation system. Compaq Professional Workstation AP200 Reference Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
6-13
Compaq Professional Workstation AP200 Reference Guide
Solving Hardware Installation
Problems
You may need to reconfigure the workstation
when you add or remove
hardware, such as an additional diskette drive. To reconfigure the workstation
in Windows NT Workstation 4.0 after installing new hardware, run the
Computer Setup utility. See Chapter 2, “Software,” for more information on
Computer Setup.
Table 6-6
Solving Hardware Installation Problems
Problem
Cause
Solution
A new device is not
recognized as part of the
workstation system
The workstation needs to be
reconfigured to recognize the
device.
Follow the reconfiguration
instructions above.
Cable(s) of new external device
are loose or power cables are
unplugged.
Ensure that all cables are properly
and securely connected and that
pins in the cable or connector are
not bent down.
Power switch of new external
device is not turned on.
Turn off the workstation, turn on
the external device, then turn on
the workstation to integrate the
device with the workstation
system.