Compaq AP200 Reference Guide - Page 95

Removing a Drive from a Drive Bay

Get Compaq AP200 - Professional - 128 MB RAM PDF manuals and user guides
UPC - 743172868534
View all Compaq AP200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

4-31 Removing a Drive from a Drive Bay IMPORTANT: Compaq does not support mixing IDE ATA and SCSI hard drives in the same system. If you are replacing a hard drive in bay 4 or 5, it must be of the same type. 1. Turn off the workstation and any external devices. Disconnect the power cord from the grounded AC outlet. Disconnect the network cable and any external devices from the system. Then remove the workstation access panel. IMPORTANT: On a power-managed system, the power cord MUST be disconnected from the grounded AC outlet. 2. Remove the front bezel. 3. Disconnect the drive power and signal cables and, if it is a CD-ROM drive, disconnect the audio connector. 4. Press the drivelock to unlock the drive in the drive bay. Figure 4-24. Releasing the drives with the drivelock 5. While pressing the drivelock, pull the drive out of the drive bay. Compaq Professional Workstation AP200 Reference Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
4-31
Compaq Professional Workstation AP200 Reference Guide
Removing a Drive from a Drive Bay
IMPORTANT:
Compaq does not support mixing IDE ATA and SCSI hard
drives in the same system. If you are replacing a hard drive in bay 4 or 5, it
must be of the same type.
1.
Turn off the workstation and any external devices. Disconnect the
power cord from the grounded AC outlet. Disconnect the network
cable and any external devices from the system. Then remove the
workstation access panel.
IMPORTANT:
On a power-managed system, the power cord MUST be
disconnected from the grounded AC outlet.
2.
Remove the front bezel.
3.
Disconnect the drive power and signal cables and, if it is a CD-ROM
drive, disconnect the audio connector.
4.
Press the drivelock to unlock the drive in the drive bay.
Figure 4-24.
Releasing the drives with the drivelock
5.
While pressing the drivelock, pull the drive out of the drive bay.