Compaq AP200 Reference Guide - Page 91

Installing a 3.5-Inch Drive into the Third-height, 5.25-Inch Drive Bay

Get Compaq AP200 - Professional - 128 MB RAM PDF manuals and user guides
UPC - 743172868534
View all Compaq AP200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

4-27 1 2 3 Figure 4-19. Connecting the drive cables to the system board: 1 IDE diskette drive connector, 2 IDE Ultra ATA hard drive connector 3 IDE CD-ROM connector 5. Remove the bezel blank from the subpanel inside the front bezel. See the section "Removing the Bezel Blank." 6. Replace the workstation access panel. 7. Plug the network cable back into the system. Plug the power cord back into the grounded AC outlet. Reconnect external devices. 8. Reconfigure the workstation, if necessary. See the "When to Reconfigure the Workstation" section in this chapter. Installing a 3.5-Inch Drive into the Third-height, 5.25-Inch Drive Bay 1. Turn off the workstation and any external drives. Disconnect the power cord from the grounded AC outlet. Disconnect the network cable and any external devices from the system. Then remove the workstation access panel. IMPORTANT: On a power-managed system, the power cord MUST be disconnected from the grounded AC outlet. 2. Remove the front bezel. 3. Install one guide screw on the right side of the drive. Compaq Professional Workstation AP200 Reference Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
4-27
Compaq Professional Workstation AP200 Reference Guide
1
2
3
Figure 4-19.
Connecting the drive cables to the system board:
1
IDE diskette drive
connector,
2
IDE Ultra ATA hard drive connector
3
IDE CD-ROM connector
5.
Remove the bezel blank from the subpanel inside the front bezel. See
the section “Removing the Bezel Blank.”
6.
Replace the workstation access panel.
7.
Plug the network cable back into the system. Plug the power cord back
into the grounded AC outlet. Reconnect external devices.
8.
Reconfigure the workstation, if necessary. See the “When to
Reconfigure the Workstation” section in this chapter.
Installing a 3.5-Inch Drive into the
Third-height, 5.25-Inch Drive Bay
1.
Turn off the workstation and any external drives. Disconnect the power
cord from the grounded AC outlet. Disconnect the network cable and
any external devices from the system. Then remove the workstation
access panel.
IMPORTANT:
On a power-managed system, the power cord MUST be
disconnected from the grounded AC outlet.
2.
Remove the front bezel.
3.
Install one guide screw on the right side of the drive.