Dell Dimension 8200 Dell Dimension 8200 Systems Solutions Guide - Page 80

Replacing the AGP Card, My Computer, Properties, General - ram

Get Dell Dimension 8200 PDF manuals and user guides View all Dell Dimension 8200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

www.dell.com | support.dell.com 11 Right-click the My Computer icon and then click Properties. 12 Click the General tab. 13 To verify that the memory is installed correctly, check the amount of memory (RAM) listed. Replacing the AGP Card CAUTION: Before you begin any of the procedures in this section, follow the safety instructions listed in "When Working Inside Your Computer" on page 12. 1 Shut down the computer (see page 20). 2 Turn off any attached devices and disconnect them from their electrical outlets. NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network wall jack. 3 Disconnect the computer power cable from the wall outlet, and then press the power button to ground the system board. 4 Open the computer cover (see page 67). 5 Press the card clip lever on the side of the AGP card to release the card from the slot connector, and remove the card. AGP card card clip lever AGP card clip slot connector back of computer 6 To replace the AGP card, gently press it down into the slot connector until it clicks into place. Press the card clip lever while inserting the card into the slot connector. 80 Adding Parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
80
Adding Parts
www.dell.com | support.dell.com
11
Right-click the
My Computer
icon and then click
Properties
.
12
Click the
General
tab.
13
To verify that the memory is installed correctly, check the amount of
memory (RAM) listed.
Replacing the AGP Card
CAUTION: Before you begin any of the procedures in this section,
follow the safety instructions listed in "When Working Inside Your
Computer" on page 12.
1
Shut down the computer (see page 20).
2
Turn off any attached devices and disconnect them from their
electrical outlets.
NOTICE:
To disconnect a network cable, first unplug the cable from your
computer and then unplug it from the network wall jack.
3
Disconnect the computer power cable from the wall outlet, and then
press the power button to ground the system board.
4
Open the computer cover (see page 67).
5
Press the card clip lever on the side of the AGP card to release the card
from the slot connector, and remove the card.
6
To replace the AGP card, gently press it down into the slot connector
until it clicks into place. Press the card clip lever while inserting the
card into the slot connector.
card clip
lever
AGP card
AGP card clip
slot connector
back of computer