Dell Dimension 8200 Dell Dimension 8200 Systems Solutions Guide - Page 84

Adding Other Drives

Get Dell Dimension 8200 PDF manuals and user guides View all Dell Dimension 8200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

www.dell.com | support.dell.com HINT: Your computer uses cable-select drive cables. This means that the device connected to the end connector of the drive cable is the master device and the device connected to the middle connector is the slave device. Be sure that the jumper setting on the new device is set for "cable select" (see the documentation that came with the drive for information). power cable second hard-drive cable (secondary drive) first hard-drive cable (primary boot drive) 12 Close the computer cover (see page 90). 13 Connect your computer and devices to their electrical outlets, and turn them on. NOTICE: To connect a network cable, first plug the cable in to the network wall jack and then plug it in to the computer. 14 See the documentation that came with the drive for instructions on installing any software required for drive operation. Adding Other Drives CAUTION: Before you begin any of the procedures in this section, follow the safety instructions listed in "When Working Inside Your Computer" on page 12. 84 Adding Parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
84
Adding Parts
www.dell.com | support.dell.com
HINT:
Your computer
uses cable-select drive
cables. This means that
the device connected to
the end connector of the
drive cable is the master
device and the device
connected to the middle
connector is the slave
device. Be sure that the
jumper setting on the new
device is set for "cable
select" (see the
documentation that came
with the drive for
information).
12
Close the computer cover (see page 90).
13
Connect your computer and devices to their electrical outlets, and
turn them on.
NOTICE:
To connect a network cable, first plug the cable in to the network
wall jack and then plug it in to the computer.
14
See the documentation that came with the drive for instructions on
installing any software required for drive operation.
Adding Other Drives
CAUTION: Before you begin any of the procedures in this section,
follow the safety instructions listed in "When Working Inside Your
Computer" on page 12.
power cable
first hard-drive
cable (primary
boot drive)
second hard-drive
cable (secondary
drive)