Dell PowerEdge 840 Hardware Owner's Manual (PDF) - Page 46

Installing the Front-Panel Drive Inserts, CAUTION, NOTICE

Get Dell PowerEdge 840 PDF manuals and user guides View all Dell PowerEdge 840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Figure 3-4. Removing the Front-Panel Drive Inserts 1 2 1 chassis drive insert 2 bezel drive insert Installing the Front-Panel Drive Inserts CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. Before performing any procedure, see your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. NOTICE: You must install both inserts in an empty 5.25-inch drive bay to maintain Federal Communications Commission (FCC) certification of the system. The inserts also help keep dust and dirt out of the system. 1 Install the chassis drive insert by sliding the insert into the chassis until tabs on the side of the insert snap into place. See Figure 3-4. 2 Install the bezel drive insert by sliding the insert into the bezel until the tabs on the side of the insert snap into place. See Figure 3-4. 3 Install the bezel. See "Installing the Bezel" on page 47. 4 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. 46 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
46
Installing System Components
Figure 3-4.
Removing the Front-Panel Drive Inserts
Installing the Front-Panel Drive Inserts
CAUTION:
Only trained service technicians are authorized to remove the system cover and access any of the
components inside the system. Before performing any procedure, see your
Product Information Guide
for complete
information about safety precautions, working inside the computer, and protecting against electrostatic discharge.
NOTICE:
You must install both inserts in an empty 5.25-inch drive bay to maintain Federal Communications
Commission (FCC) certification of the system. The inserts also help keep dust and dirt out of the system.
1
Install the chassis drive insert by sliding the insert into the chassis until tabs on the side of the insert
snap into place. See Figure 3-4.
2
Install the bezel drive insert by sliding the insert into the bezel until the tabs on the side of the insert
snap into place. See Figure 3-4.
3
Install the bezel. See "Installing the Bezel" on page 47.
4
Reconnect the system to its electrical outlet and turn the system on, including any attached
peripherals.
1
chassis drive insert
2
bezel drive insert
1
2