Dell PowerEdge 840 Hardware Owner's Manual (PDF) - Page 71

Expansion Cards, Slot 1 is a x8 lane-width PCI-Express expansion slot.

Get Dell PowerEdge 840 PDF manuals and user guides View all Dell PowerEdge 840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

4 Connect the DC power cables to the following components: • POWER CONN connector on the backplane board (if applicable) • PWR_CONN and 12V connectors on the system board • Hard drives or SAS backplane. • Diskette drive (if applicable) • Optical drive (if applicable) • Tape backup drive (if applicable) 5 Close the system. See "Closing the System" on page 47. 6 Stand the system upright. 7 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. Expansion Cards Your system supports up to five full-length expansion cards, installed in connectors on a riser card. The expansion slots are configured as follows: - Slot 1 is a x8 lane-width PCI-Express expansion slot. - Slot 2 is a x1 lane-width PCI-Express expansion slot. - Slots 3 and 4 are 3.3-V, 64-bit, 133-MHz PCI-X expansion slots. - Slot 5 is a 5-V, 32-bit, 33-MHz legacy PCI expansion slot. Figure 3-18 shows the relative locations of the expansion-card slots. NOTICE: If you install a RAC card, it must be installed in PCI slot SLOT_5. Installing System Components 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Installing System Components
71
4
Connect the DC power cables to the following components:
•
POWER CONN connector on the backplane board (if applicable)
•
PWR_CONN and 12V connectors on the system board
•
Hard drives or SAS backplane.
•
Diskette drive (if applicable)
•
Optical drive (if applicable)
•
Tape backup drive (if applicable)
5
Close the system. See "Closing the System" on page 47.
6
Stand the system upright.
7
Reconnect the system to its electrical outlet and turn the system on, including any attached
peripherals.
Expansion Cards
Your system supports up to five full-length expansion cards, installed in connectors on a riser card. The
expansion slots are configured as follows:
–
Slot 1 is a x8 lane-width PCI-Express expansion slot.
–
Slot 2 is a x1 lane-width PCI-Express expansion slot.
–
Slots 3 and 4 are 3.3-V, 64-bit, 133-MHz PCI-X expansion slots.
–
Slot 5 is a 5-V, 32-bit, 33-MHz legacy PCI expansion slot.
Figure 3-18 shows the relative locations of the expansion-card slots.
NOTICE:
If you install a RAC card, it must be installed in PCI slot SLOT_5.