Denon AVR-1912 Owners Manual - Page 90

Basic version Advanced version Audio Setup Default settings are underlined. Make settings for audio playback. Setting items 2ch Direct/Stereo Select the method for setting the speakers used in the 2-channel direct and stereo playback modes. Setting details Setting : Select the method for setting the speakers used in the 2-channel direct and stereo playback modes. • Basic : The settings at "Speaker Setup" (vpage 83) are applied. • Custom : Make separate settings for 2-channel. Make the following settings: Front : Set the front speaker size. • Large : Use a large speaker that can adequately play back low frequencies. • Small : Use a small speaker that has inadequate playback capacity for low frequencies. If "Speaker Config." - "Subwoofer" (vpage 83) is set to "No", the setting is automatically set to "Large". SW : Set the presence of a subwoofer. • Yes : Use a subwoofer. • No : Select when a subwoofer is not connected. If "Speaker Config." - "Subwoofer" (vpage 83) is set to "No", the setting is automatically set to "No". If the "Front" setting is "Small", the setting is automatically "Yes". SW Mode : Select low range signals to be reproduced by subwoofer. • LFE : When the "2ch Direct/Stereo" - "Front" setting is set to "Large", the LFE signal alone is output from the subwoofer. Also, when the "2ch Direct/Stereo" - "Front" setting is set to "Small", the front channel low range signal is added to the LFE signal output from the subwoofer. • LFE+Main : The front channel low range signal is added to the LFE signal output from the subwoofer. This setting can be set made "2ch Direct/Stereo" - "SW" is set to "Yes". Crossover : Set the maximum frequency of the bass signal output from each channel to the subwoofer. • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz System Setup Setting items 2ch Direct/Stereo (Continued) Setting details Distance FL / Distance FR : Select the speaker. • 0.0ft - 60.0ft (12.0ft) / 0.00m - 18.00m (3.60m) : Set the distance to the speaker. Auto Surround Make setting for memorizing surround mode setting for each input signal type. Set the difference in the distance between the speakers to less than 20.0 ft (6.00 m). Level FL / Level FR : Select the speaker. • -12.0dB - +12.0dB (0.0dB) : Adjust the level of each channel. ON : Memorize settings. Automatically play with the last used surround mode. OFF : Do not memorize settings. Surround mode does not change according to input signal. • The auto surround mode function lets you store in the memory the surround mode last used for playing the four types of input signals listed below. q Analog and PCM 2-channel signals w Dolby Digital and DTS 2-channel signals e Dolby Digital and DTS multi-channel signals r LPCM Multi-channel signals • When playing in PURE DIRECT, the surround mode does not change even if the input signal is changed. EQ Customize Audyssey Byp. L/R : Set when not using "Audyssey Byp. L/R" equalizer. Set the equalizers that • Used : Use. will not be used to not • Not Used : Do not use. be displayed when the "MultEQ®" equalizer is selected. Set so that "Audyssey Byp. L/R" settings can be made when Audyssey® Auto Setup is performed. Audyssey Flat : Set when not using "Audyssey Flat" equalizer. • Used : Use. The equalizer mode in which • Not Used : Do not use. "Not Used" is selected Set so that "Audyssey Flat" settings can be made when Audyssey® cannot be stored and Auto Setup is performed. recalled in the Quick Select Manual : Set when not using the "Manual" equalizer. function. • Used : Use. • Not Used : Do not use. • This setting can be set made "2ch Direct/Stereo" - "SW" is set to "Yes". • If the "2ch Direct/Stereo" - "Front" setting is "Large" and the "SW Mode" setting is "LFE", "Full Band" is displayed and the setting cannot be made. Information BD 87